FT245RQ-REEL FTDI, FT245RQ-REEL Datasheet - Page 25

• Manufacturer Part Number: FT245RQ-REEL
• Description: USB Interface IC USB to Parallel FIFO Enhanced IC QFN-32
• Manufacturer: FTDI

Specifications of FT245RQ-REEL

• Mounting Style: SMD/SMT
• Package / Case: QFN
• Lead Free Status / RoHS Status: Lead free / RoHS Compliant

7.4 USB Bus Powered with Selectable External Logic Supply
Figure 7.4 USB Bus Powered with +3.3V or +5V External Logic Power Supply
Figure 7.4 illustrates a USB bus power application with selectable external logic supply. The external logic
can be selected between +3.3V and +5V using the jumper switch. This jumper is used to allow the
FT245R to be interfaced with a +3.3V or +5V logic devices. The VCCIO pin is either supplied with +5V
from the USB bus (jumper pins1 and 2 connected), or from the +3.3V output from the FT245R 3V3OUT
pin (jumper pins 2 and 3 connected). The supply to VCCIO is also used to supply external logic.
With bus powered applications, the following should be noted:
Another possible configuration could use a discrete low dropout (LDO) regulator which is supplied by the
5V on the USB bus to supply between +1.8V and +2.8V to the VCCIO pin and to the external logic. In
this case VCC would be supplied with the +5V from the USB bus and the VCCIO would be supplied from
the output of the LDO regulator. This results in the FT245R I/O pins driving out at between +1.8V and
+2.8V logic levels.
For a USB bus powered application, it is important to consider the following when selecting the regulator:
A suitable series of LDO regulators that meets these requirements is the MicroChip/Telcom
(www.microchip.com) TC55 series of devices. These devices can supply up to 250mA current and have a
quiescent current of under 1μA.
v) PWREN# gets its VCC from VCCIO. For designs using 3V3 logic, ensure VCCIO is not powered
i)
ii)
i)
ii)
SHIELD
5
down using the external logic. In this case use the +3V3OUT.
To comply with the 2.5mA current supply limit during USB suspend mode, PWREN# or
SLEEP# signals should be used to power down external logic in this mode. If this is not
possible, use the configuration shown in Section 9.
The maximum current sourced from the USB bus during normal operation should not exceed
100mA, otherwise a bus powered design with power switching (Section 7.3) should be used.
The regulator must be capable of sustaining its output voltage with an input voltage of
+4.35V. An Low Drop Out (LDO) regulator should be selected.
The quiescent current of the regulator must be low enough to meet the total current
requirement of <= 2.5mA during USB suspend mode.
Copyright © 2010 Future Technology Devices International Limited
1
2
3
4
10nF
100nF
GND
+
Ferrite
Bead
4.7uF
GND
Jumper
Vcc
+
2
3
1
Vcc
100nF
VCCIO
FT245R USB FIFO IC Datasheet Version 2.10
GND
VCC
USBDM
USBDP
3V3OUT
VCCIO
NC
OSCI
RESET#
OSCO
NC
G
A
N
D
G
N
D
FT245R
G
N
D
Document No.: FT_000052
GND
G
Clearance No.: FTDI# 39
N
D
E
S
T
T
PWREN#
RXF#
TXE#
WR#
RD#
D0
D1
D2
D3
D4
D5
D6
D7
3.3V or 5V Supply
to External Logic
100nF
VCCIO
10k
25