CSBLA455KJ58-B0 Murata, CSBLA455KJ58-B0 Datasheet - Page 47

• Manufacturer Part Number: CSBLA455KJ58-B0
• Description: Resonators 455kHz 0.5%
• Manufacturer: Murata
• Series: CSBLAr

Specifications of CSBLA455KJ58-B0

• Tolerance: 0.5 %
• Termination Style: SMD/SMT
• Operating Temperature Range: - 20 C to + 80 C
• Dimensions: 3.5 mm W x 7 mm L x 9 mm H
• Frequency: 455 KHz
• Frequency Tolerance: ± 0.5%
• Oscillator Mounting: Through Hole
• No. Of Pins: 2
• Features: Piezoelectric Ceramic
• Rohs Compliant: Yes
• Resonator Case: Radial Leaded
• Resonant Impedance: 30ohm
• Lead Free Status / RoHS Status: Lead free / RoHS Compliant

!Note
• This PDF catalog is downloaded from the website of Murata Manufacturing co., ltd. Therefore, it’s specifications are subject to change or our products in it may be discontinued without advance notice. Please check with our
• This PDF catalog has only typical specifications because there is no space for detailed specifications. Therefore, please approve our product specifications or transact the approval sheet for product specifications before ordering.
sales representatives or product engineers before ordering.
!Note
CSBLA_E
The component cannot withstand washing.
Please do not apply excessive mechanical stress to the
component and lead terminals during soldering.
CSBLA_J
(1) Cleaning Solvents
(2) Temperature Difference: dT *1
(3) Conditions
CSBLA_E
1. Product Storage Condition
2. Expiration Date on Storage
3. Notice on Product Storage
(1) Please do not store the products in a chemical
Soldering and Mounting
Soldering and Mounting
Storage and Operating Conditions
Please store the products in a room where the
temperature/humidity is stable, and avoid
such places where there are large temperature
changes. Please store the products under the
following conditions:
Expiration date (Shelf life) of the products is six
months after delivery under the conditions of a
sealed and unopened package. Please use the
products within six months after delivery. If you
store the products for a long time (more than six
months), use carefully because the products may
be degraded in solderability and/or rusty.
Please confirm solderability and characteristics
for the products regularly.
HCFC, Isopropanol, Tap water, Demineralized water,
dT<=30 C. (dT=Component-solvent)
1. Ultrasonic Wash
2. Immersion Wash
3. Shower or Rinse Wash
Temperature: -10 to + 40 degrees C
Humidity: 15 to 85% R.H.
Cleanthrough750H, Pine alpha 100S, Techno care
FRW.
*1 ex. In case the component at +90 degree C. immerses
atmosphere (Acids, Alkali, Bases, Organic gas,
Sulfides and so on), because the characteristics
may be reduced in quality, and/or be degraded in
the solderability due to the storage in a
chemical atmosphere.
• Please read rating and !CAUTION (for storage, operating, rating, soldering, mounting and handling) in this catalog to prevent smoking and/or burning, etc.
• This catalog has only typical specifications because there is no space for detailed specifications. Therefore, please approve our product specifications or transact the approval sheet for product specifications before ordering.
1 minute max. in above solvent at +60 degree C. max.
(Frequency: 28kHz, Output: 20W/L)
5 minutes max. in above solvent at +60 degree C. max.
5 minutes max. in above solvent at +60 degree C. max.
into cleaning solvent at +60 degree C., then
dT=30 degree C.
Notice for General Usage -kHz Lead Type-
(4) Drying
(5) Others
4. Others
(2) Please do not put the products directly on the
(3) Please do not store the products in places
(4) Please use the products immediately after the
(5) Please do not drop the products to avoid cracking
Conformal coating or washing of the component is not
acceptable because it is not hermetically sealed.
Please be sure to consult with our sales representatives
or engineers whenever and prior to using the products.
5 minutes max. by air blow at +80 degree C. max.
1. Total washing time should be within 10 minutes.
2. Please ensure the component is thoroughly
3. The component may be damaged if it is washed
4. Please do not apply excessive mechanical stress to
5. Ultrasonic cleaning of the component is acceptable.
floor without anything under them to avoid damp
and/or dusty places.
such as: in a damp heated place, in a place where
direct sunlight comes in, in a place applying
vibrations.
package is opened, because the characteristics
may be reduced in quality, and/or be degraded in
the solderability due to storage under the poor
conditions.
of ceramic elements.
evaluated in your application circuit.
with alkali cleaning solvent.
the component and lead terminals during soldering.
However, the size of bath, size and thickness of
PBC should be evaluated to confirm stable electrical
characteristics are maintained.
45
P16E.pdf
10.12.7
7