MMA7330LT Freescale Semiconductor, MMA7330LT Datasheet - Page 3

IC ACCELEROMETER 4G-12G 14-LGA

MMA7330LT

Manufacturer Part Number
MMA7330LT
Description
IC ACCELEROMETER 4G-12G 14-LGA
Manufacturer
Freescale Semiconductor
Datasheet

Specifications of MMA7330LT

Axis
X, Y, Z
Acceleration Range
±4g, 12g (Config)
Sensitivity
308mV/g, 83.6mV/g
Voltage - Supply
2.2 V ~ 3.6 V
Output Type
Analog
Bandwidth
400Hz - XY, 300Hz - Z
Interface
Parallel
Mounting Type
Surface Mount
Package / Case
14-LGA
Sensing Axis
X, Y, Z
Acceleration
4 g, 12 g
Supply Voltage (max)
3.6 V
Supply Voltage (min)
- 0.3 V
Supply Current
400 uA
Maximum Operating Temperature
+ 85 C
Minimum Operating Temperature
- 40 C
Mounting Style
SMD/SMT
Lead Free Status / RoHS Status
Lead free / RoHS Compliant
Table 2. Operating Characteristics
Unless otherwise noted: –20°C < T
1. For a loaded output, the measurements are observed after an RC filter consisting of an internal 32kΩ resistor and an external 3.3nF capacitor
2. These limits define the range of operation for which the part will meet specification.
3. Within the supply range of 2.2 and 3.6 V, the device operates as a fully calibrated linear accelerometer. Beyond these supply limits the device
4. This value is measured with g-Select in 4g mode.
5. The device can measure both + and – acceleration. With no input acceleration the output is at midsupply. For positive acceleration the output
6. For optimal 0g offset performance, adhere to AN3484 and AN3447.
7. The response time between 10% of full scale Vdd input voltage and 90% of the final operating output voltage.
8. The response time between 10% of full scale Sleep Mode input voltage and 90% of the final operating output voltage.
9. The response time between 10% of the full scale self test input voltage and 90% of the self test output voltage.
10. A measure of the device’s ability to reject an acceleration applied 90° from the true axis of sensitivity.
Sensors
Freescale Semiconductor
Operating Range
Output Signal
Self Test
Noise
Control Timing
Output Stage Performance
Nonlinearity, X
Cross-Axis Sensitivity
Supply Voltage
Supply Current
Supply Current at Sleep Mode
Operating Temperature Range
Acceleration Range, X-Axis, Y-Axis, Z-Axis
Zero g (T
Zero g
Sensitivity (T
Sensitivity
Bandwidth Response
Output Impedance
Output Response
Input Low
Input High
Power Spectral Density RMS (0.1 Hz – 1 kHz)
Power-Up Response Time
Enable Response Time
Self Test Response Time
Sensing Element Resonant Frequency
Internal Sampling Frequency
Full-Scale Output Range (I
(recommended as a minimum to filter clock noise) on the analog output for each axis and a 0.1μF capacitor on V
bandwidth is determined by the Capacitor added on the output. f = 1/2π * (32 x 10
the minimum to filter out internal clock noise.
may operate as a linear device but is not guaranteed to be in calibration.
will increase above V
g-Select: 0
g-Select: 1
4g
12g
XY
Z
X
Z
XY
Z
OUT
OUT
(4)
, Y
A
(4)
OUT
= 25°C, V
OUT
A
= 25°C, V
(2)
(4)
(3)
, Y
OUT
(10)
DD
DD
, Z
(8)
/2. For negative acceleration, the output will decrease below V
= 2.8 V)
DD
Characteristic
(9)
OUT
(7)
OUT
= 2.8 V)
(4)
= 30 µA)
(5), (6)
A
< 85°C, 2.2 V < V
(4)
DD
< 3.6 V, Acceleration = 0g, Loaded output
t
V
RESPONSE
V
f
Symbol
t
GCELLXY
f
XY, XZ, YZ
Δg
f
NL
ENABLE
GCELLZ
Δg
OFF
-3dBXY
f
V
n
V
S,T
S
-3dBZ
V
f
g
g
S
V
I
I
V
t
Z
CLK
T
PSD
DD
DD
OFF
STXY
FSO
ST
12g
DD
FS
FS
OUT
STZ
4g
IH
O
IL
A
, T
A
A
3
) * C. C = 3.3 nF corresponds to BW = 1507HZ, which is
DD
V
0.7 V
1.316
289.5
+0.05
SS
/2.
75.2
+0.8
Min
V
-1.0
-5.0
2.2
-40
SS
+0.1
DD
±0.03
±2.0
83.6
+1.0
Typ
-0.1
400
±12
308
400
300
350
2.8
1.4
1.0
0.5
2.0
6.0
3.4
±4
32
11
3
(1)
DD
- GND. The output sensor
V
0.3 V
1.484
326.5
DD
Max
91.9
+1.2
+1.0
+5.0
V
600
+85
3.6
2.0
2.0
5.0
10
DD
–0.1
DD
MMA7330L
μg/
%FSO
mg/°C
mV/g
mV/g
%/°C
Unit
kHz
kHz
kHz
μA
μA
Hz
Hz
ms
ms
ms
°C
%
V
V
V
V
V
g
g
g
g
Hz
3

Related parts for MMA7330LT