LP8900TLX-3333 National Semiconductor, LP8900TLX-3333 Datasheet - Page 5

• Manufacturer Part Number: LP8900TLX-3333
• Description: REG ULN, DUAL, 200MA, 6-MICROSMD
• Manufacturer: National Semiconductor

Specifications of LP8900TLX-3333

• Primary Input Voltage: 3.8V
• Output Voltage: 3.6V
• Dropout Voltage Vdo: 110mV
• No. Of Pins: 6
• Output Current: 200mA
• Operating Temperature Range: -40°C To +125°C
• Svhc: No SVHC (15-Dec-2010)
• Operating: RoHS Compliant
• Output Voltage Fixed: 3.6V
• Voltage Regulator Case Style: Micro SMD
• Rohs Compliant: Yes

Enable Control Characteristics
I
V
V
Timing\Transient Characteristics(Note 14)
T
T
Transient
Response
C
C
EN
ON
OFF
IL
IH
IN
OUT
Electrical Characteristics con't.
Unless otherwise noted, V
V
Typical values and limits appearing in normal type apply for T
temperature range for operation, −40 to +125°C. (Note 9)
Symbol
Note 1: Absolute Maximum Ratings are limits beyond which damage can occur. Operating Ratings are conditions under which operation of the device is
guaranteed. Operating Ratings do not imply guaranteed performance limits. For guaranteed performance limits and associated test conditions, see the Electrical
Characteristics tables.
Note 2: All Voltages are with respect to the potential at the GND pin.
Note 3: For further information on these packages please refer to the following application notes,AN-1112 Micro SMD Wafer Level Chip Scale Package.
Note 4: Internal thermal shutdown circuitry protects the device from permanent damage.
Note 5: The human body model is 100pF discharged through a 1.5kΩ resistor into each pin. The machine model is a 200pF capacitor discharged directly into
each pin.
Note 6: The maximum ambient temperature (T
dissipation of the device in the application (P
following equation: T
Note 7: Junction to ambient thermal resistance is dependant on the application and board layout. In applications where high maximum power dissipation is
possible, special care must be paid to thermal dissipation issues in board design.
Note 8: Full details can be found in JESD61-7
Note 9: All limits are guaranteed. All electrical characteristics having room-temperature limits are tested during production at T
Statistical Quality Control methods. Operation over the temperature specification is guaranteed by correlating the electrical characteristics to process and
temperature variations and applying statistical process control.
Note 10: The minimum input voltage = V
Note 11: Dropout voltage is voltage difference between input and output at which the output voltage drops to 100mV below its nominal value. This parameter is
only specified for output voltages above 1.8V.
Note 12: The device maintains the regulated output voltage without a load.
Note 13: Short circuit current is measured with V
Note 14: This electrical specification is guaranteed by design.
Note 15: Enable Pin has an internal 3MΩ typical, resistor connected to GND.
Note 16: The capacitor tolerance should be 30% or better over temperature. The full operating conditions for the application should be considered when selecting
a suitable capacitor to ensure that the minimum value of capacitance is always met. Recommended capacitor type is X7R or X5R. (See capacitor section in
Applications Hints)
Recommended Capacitor Specifications
OUT2.
Symbol
C
IN
= C
Maximum Input Current at
V
Low Input Threshold
High Input Threshold
Turn On Time
Turn Off Time
Line Transient Response |δV
Load Transient Response |δV
Overshoot on Start-up
EN
OUT
Input(Note 15)
Input Capacitor
Output Capacitor
A(max)
= 1µF, I
= T
Parameter
J(max-op)
Parameter
OUT
EN
=1.2V, V
= 1mA.
- (θ
OUT(NOM)
JA
× P
D(max)
A(max)
IN
D(max)
OUT
+ 0.5V or 1.8V, whichever is greater.
= V
), and the junction to ambient thermal resistance of the part / package in the application (θ
OUT
OUT
) is dependant on the maximum operating junction temperature (T
).
pulled to 0V.
OUT
| T
| T
Capacitance
(Note 16)
ESR
V
V
V
V
To 95% Level
V
5% of V
δV
+ 0.5V, or 1.8V, whichever is higher, where V
rise
rise
EN
EN
IN
IN
OUT(nom)
IN
= 1.8V to 5.5V
= 1.8V to 5.5V
= 0V, V
= V
= T
= T
= 600mV
IN
OUT(NOM),
fall
fall
= 5.5V
= 30µs
= 1µs I
IN
A
= 25°C. Limits appearing in boldface type apply over the full junction
Conditions
Conditions
= 5.5V
5
I
OUT
I
OUT
OUT
= 0mA
= 1 mA to 200mA
= 200mA to 1mA
0.003
Typ
Typ
0.4
1.0
1.0
80
80
70
1
0
OUT
J(max-op)
is the higher of V
0.33
0.33
Min
Min
= 125°C), the maximum power
J
1.2
5
= 25°C or correlated using
Limit
Limit
Max
Max
200
500
4.7
0.4
10
JA
4
1
1
OUT1
), as given by the
www.national.com
and
(pk - pk)
Units
Units
mV
mV
mΩ
µA
ms
µF
µs
%
V
V