PIC16F884-E/P Microchip Technology, PIC16F884-E/P Datasheet - Page 117

• Manufacturer Part Number: PIC16F884-E/P
• Description: IC,MICROCONTROLLER,8-BIT,PIC CPU,CMOS,DIP,40PIN,PLASTIC
• Manufacturer: Microchip Technology
• Series: PIC® 16Fr

Specifications of PIC16F884-E/P

• Rohs Compliant: YES
• Core Processor: PIC
• Core Size: 8-Bit
• Speed: 20MHz
• Connectivity: I²C, SPI, UART/USART
• Peripherals: Brown-out Detect/Reset, POR, PWM, WDT
• Number Of I /o: 35
• Program Memory Size: 7KB (4K x 14)
• Program Memory Type: FLASH
• Eeprom Size: 256 x 8
• Ram Size: 256 x 8
• Voltage - Supply (vcc/vdd): 2 V ~ 5.5 V
• Data Converters: A/D 14x10b
• Oscillator Type: Internal
• Operating Temperature: -40°C ~ 125°C
• Package / Case: 40-DIP (0.600", 15.24mm)
• Lead Free Status / RoHS Status: Lead free / RoHS Compliant
• For Use With: DVA18XP400 - DEVICE ADAPTER 18F4220 PDIP 40LD
• Lead Free Status / RoHS Status: Lead free / RoHS Compliant

10.1.4
To read a program memory location, the user must
write the Least and Most Significant address bits to the
EEADR and EEADRH registers, set the EEPGD con-
trol bit of the EECON1 register, and then set control bit
RD. Once the read control bit is set, the program mem-
ory Flash controller will use the second instruction
cycle to read the data. This causes the second instruc-
tion immediately following the “BSF
instruction to be ignored. The data is available in the
very next cycle, in the EEDAT and EEDATH registers;
therefore, it can be read as two bytes in the following
instructions.
EXAMPLE 10-3:
© 2009 Microchip Technology Inc.
;
;
BANKSEL EEADR
MOVLW
MOVWF
MOVLW
MOVWF
BANKSEL EECON1
BSF
BSF
NOP
NOP
BANKSEL EEDAT
MOVF
MOVWF
MOVF
MOVWF
BCF
READING THE FLASH PROGRAM
MEMORY
MS_PROG_EE_ADDR
EEADRH
LS_PROG_EE_ADDR
EEADR
EECON1, EEPGD
EECON1, RD
EEDAT, W
LOWPMBYTE
EEDATH, W
HIGHPMBYTE
STATUS, RP1
FLASH PROGRAM READ
EECON1,RD”
;
;
;MS Byte of Program Address to read
;
;LS Byte of Program Address to read
;
;Point to PROGRAM memory
;EE Read
;First instruction after BSF EECON1,RD executes normally
;Any instructions here are ignored as program
;memory is read in second cycle after BSF EECON1,RD
;
;W = LS Byte of Program Memory
;
;W = MS Byte of Program EEDAT
;
;Bank 0
PIC16F882/883/884/886/887
EEDAT and EEDATH registers will hold this value until
another read or until it is written to by the user.
Note 1: The two instructions following a program
2: If the WR bit is set when EEPGD = 1, it
memory read are required to be NOPs.
This prevents the user from executing a
two-cycle
instruction after the RD bit is set.
will be immediately reset to ‘0’ and no
operation will take place.
instruction
DS41291F-page 115
on
the
next