HMC1052 Honeywell Microelectronics & Precision Sensors, HMC1052 Datasheet
HMC1052
Specifications of HMC1052
Available stocks
Related parts for HMC1052
HMC1052 Summary of contents
Page 1
... The Honeywell HMC1051Z, HMC1051ZL, HMC1052L and HMC1053 are magnetoresistive sensors designed for low field magnetic sensing. Various packaging options have been created from the basic HMC1052 sensor chip to create 1, 2 and 3-axis magneto-resistive sensors for cost effective and small size solutions. The advantage of the ...
Page 2
... T = -40 to 125°C, No Set/Reset -40 to 125°C, With Set/Reset A Vbridge=5V -40 to 125° perming effect on zero reading T = -40 to 125°C A (HMC1052 Only) (HMC1052) Measured from S/ -40 to 125° Current Field applied in sensitive direction T = -40 to 125°C A Min Typ Max Units 1 ...
Page 3
... Set/Reset Strap S/R- (7) HMC1051Z Pinout HONEYWELL HMC1051Z HMC1051ZL Pinout VO+ VO+ VO+ OFF+ OFF+ OFF+ GND GND GND VO- VO- VO- S/R- S/R- S/R- S/R+ S/R+ S/R+ HMC1052L Pinout BOTTOM VIEW BOTTOM VIEW OUT- OUT (B) (B) S/R- S/ S/R+ S/ GND2 GND2 7 7 (B) ( OFF- OFF OUT+ ...
Page 4
... HMC1051/HMC1052/HMC1053 HMC1053 PACKAGE OUTLINES PACKAGE DRAWING HMC1051Z (8-PIN SIP) PACKAGE DRAWING HMC1051ZL (8-PIN IN-LINE LCC) 4 HMC1053 Pinout Symbol Millimeters Inches x 10E-3 Min Max Min A 1.371 1.728 54 A1 0.101 0.249 4 B 0.355 0.483 14 D 9.829 11.253 387 E 3.810 3.988 150 e 1.270 ref H 6 ...
Page 5
... The other part types have no special profile required (handle the HMC1052L and HMC1051Z as MSL 1) and are compatible with lead eutectic or lead-free solder paste reflow profiles. Honeywell recommends the adherence to solder paste manufacturer’s guidelines. The www ...
Page 6
... HMC1051/HMC1052/HMC1053 HMC105X parts may be reworked with soldering irons, but extreme care must be taken not to overheat the copper pads (must not exceed maximum device reflow temperatures) from the part’s fiberglass substrate. Irons with a tip temperature no greater than 315°C should be used. Excessive rework risks the copper pads pulling away into the molten solder. ...
Page 7
... U1 U1 1nf 1nf 5.00k 5.00k LMV358 LMV358 5.00k 5.00k 500k 500k Vref/2 Vref/2 HMC1052 HMC1052 1nf 1nf 5.00k 5.00k LMV358 LMV358 5.00k 5.00k 500k 500k Vref/2 Vref/2 .1uf .1uf U4 U4 (2) IRF7509 (2) IRF7509 volts ...
Page 8
... By using two or three sensor circuits with HMC1051, HMC1052, or HMC1053 parts, a more omni-directional sensing pattern can be implemented. There is nothing special in choosing the resistors for the differential op-amp gain stages other than having like values (e ...
Page 9
... HMC1051/HMC1052/HMC1053 Vcc Vcc 5.0v 5.0v set/reset set/reset offset offset Alternating or Direct Current Sensing The HMC105X family sensors can be utilized in a novel way for moderate to high current sensing applications using a nearby external conductor providing the sensed magnetic field to the bridge. Figure 6 shows a HMC1051Z used as a current sensor with thermistor element performing a temperature compensation function for greater accuracy over a wide range of operational temperatures ...
Page 10
... HMC1051/HMC1052/HMC1053 Three Axis Compassing with Tilt Compensation For full three-axis compassing, the circuit depicted in Figure 7 shows both a HMC1051 and a HMC1052 used for sensing the magnetic field in three axes. Alternatively a single HMC1053 could be used for a single sensor package design. A two-axis accelerometer with digital (PWM) outputs is also shown to provide pitch and roll (tilt) sensing, to correct the three-axis magnetic sensors outputs into to the tilt-compensated two-axis heading ...
Page 11
... HMC1051Z One Axis Magnetic Sensor – 8-PIN IN-LINE LCC HMC1051ZL Two Axis Magnetic Sensors – 16-PIN LCC HMC1052L HMC1052L-TR 3,000 units/reel Three Axis Magnetic Sensors – 16-PIN LCC HMC1053 FIND OUT MORE For more information on Honeywell’s Magnetic Sensors visit us online at www.magneticsensors.com or contact us at 800-323-8295 (763-954-2474 internationally) ...