LMH0394SQE/NOPB National Semiconductor, LMH0394SQE/NOPB Datasheet - Page 13

• Manufacturer Part Number: LMH0394SQE/NOPB
• Description: IC EQUALIZER CABLE 16-LLP
• Manufacturer: National Semiconductor

Specifications of LMH0394SQE/NOPB

• Applications: Amplifier
• Interface: SPI Serial
• Voltage - Supply: 2.5V
• Package / Case: 16-WQFN Exposed Pad
• Mounting Type: Surface Mount
• Ic Interface Type: Serial, SPI
• Supply Voltage Range: 2.5V
• Power Dissipation Pd: 115mW
• Operating Temperature Range: -40°C To +85°C
• Digital Ic Case Style: LLP
• No. Of Pins: 16
• Rohs Compliant: Yes
• Operating Temperature (min): -40C
• Operating Temperature Classification: Industrial
• Operating Temperature (max): 85C
• Package Type: LLP EP
• Rad Hardened: No
• Lead Free Status / RoHS Status: Lead free / RoHS Compliant
• Other names: LMH0394SQE/NOPBTR

In the second transaction, three dummy reads (each consist-
ing of 16 “1”s) are shifted in, and the read data from Device 2
(with value 0x88) appears on MISO in the 25th through 32nd
clock cycles.
SPI Daisy-Chain Length Detection
A useful operation for the host may be to detect the length of
the daisy-chain. This is a simple matter of shifting in a series
OUTPUT DRIVER ADJUSTMENTS AND DE-EMPHASIS
SETTING
The output driver swing (amplitude), offset voltage (common
mode voltage), and de-emphasis level are adjustable via SPI
register 01h.
The output swing is adjustable via bits [7:6] of SPI register
01h. The default value for these register bits is “10” for a peak
to peak differential output voltage of 700 mV
swing can be set for 400 mV
800 mV
The offset voltage is adjustable via bits [5:4] of SPI register
01h. The default value for these register bits is “10” for an
output offset of 1.2V. The output common mode voltage may
be adjusted in 200 mV increments, from 0.8V to 1.2V. It can
be set to “11” for the maximum offset voltage. At this maxi-
mum offset voltage setting, the outputs are referenced to the
positive supply and the offset voltage is around 1.35V.
The output de-emphasis is turned on or off by bit 3 of SPI
register 01h, and the de-emphasis level is set by bits [2:1] of
SPI register 01h. The output de-emphasis level may be set
for 0 dB (for driving up to 10” FR4), 3 dB (for driving 10-20”
FR4), 5 dB (for driving 20-30” FR4), or 7 dB (for driving 30-40”
FR4).
LAUNCH AMPLITUDE OPTIMIZATION
The LMH0394 can compensate for attenuation of the input
signal prior to the equalizer. This compensation is useful for
applications with a passive splitter at the equalizer input or a
non-ideal input termination network, and is controlled by SPI
register 02h.
Bit 7 of SPI register 02h is used for the launch amplitude set-
ting. At the default setting of “0”, the LMH0394 operates
normally and expects a launch amplitude of 800 mV
may be set to “1” to optimize the LMH0394 for input signals
with 6 dB of attenuation (400 mV
P-P
.
P-P
, 600 mV
P-P
).
FIGURE 11. SPI Daisy-Chain Length Detection
P-P
, 700 mV
P-P
. The output
P-P
P-P
. Bit 7
, or
13
of dummy reads with a known data value (such as 0x5A). For
an SPI daisy-chain of N LMH0394 devices, the known data
value will appear on the host's MISO pin after N+1 writes.
Assuming a daisy-chain of three LMH0394 devices, the result
of this operation is shown in
CABLE LENGTH INDICATOR (CLI)
The cable length indicator (CLI) provides an indication of the
length of the cable attached to input. CLI is accessible via bits
[7:0] of SPI register 06h. The 8-bit setting ranges in decimal
value from 0 to 247 (“00000000” to “11110111” binary), cor-
responding to 0 to 400m of Belden 1694A cable.
shows typical CLI values vs. Belden 1694A cable length. CLI
is valid for Belden 1694A cable lengths of 0-200m at 2.97
Gbps, 0-220m at 1.485 Gbps, and 0-400m at 270 Mbps. Note:
Given the continuous adaptive nature of the equalizer, this
setting changes by some steps constantly.
FIGURE 12. CLI vs. Belden 1694A Cable Length
250
225
200
175
150
125
100
75
50
25
0
0
BELDEN 1694A CABLE LENGTH (m)
50 100 150 200 250 300 350 400
SD
3G/HD
Figure
30101529
11.
www.national.com
Figure 12
30101513