VC2GU SQUARE D, VC2GU Datasheet - Page 30

• Manufacturer Part Number: VC2GU
• Description: SWITCH, DISCONNECT, 25A, 3POLE
• Manufacturer: SQUARE D

Specifications of VC2GU

• No. Of Poles: 3
• Contact Voltage Ac Max: 600V
• Contact Current Ac Max: 25A
• Mounting Type: Panel
• Lead Free Status / RoHS Status: Lead free / RoHS Compliant

30
Remote operation shown
Alternate Mounting Kit
Auxiliary Lock Plate
(handle mechanism
not included in kit)
Channel/Flange
Support Kit
Accessories for Class 9422
Flange-Mounted, Variable-Depth Disconnect Switches
Remote or Dual Adaptor Kit
For the remote or dual operation of 30, 60, 100 and 200 ampere disconnect switches, or GJL, FAL, FHL,
KAL, KHL, LAL, LHL, Q4L, MAL, MHL, MEL, and MXL circuit breakers.
Remote Operation — permits mounting the Class 9422 Type A9 or A10 handle mechanism at a lower
level than the disconnect device it controls. This arrangement is often required where the disconnect
device is mounted too high for personnel to easily reach a conventional operator.
Dual Operation — permits controlling two disconnect devices, one in line with and one remote from a
single Class 9422 Type A9 or A10 handle mechanism.
Note: Class 9422 Type A9 or A10 handle and preferred mounting method must be used.
Mounting Depths for Remote or Dual Adaptor Kits
Note: Must mount switch or circuit breaker a minimum of 9" above or below.
Other Accessories
Disconnect Switch
30A Type TCN, TCF
60A Type TDN, TDF
100A Type TEN, TEF
200A Type TF
Circuit Breaker
GJL
FAL, FHL
KAL, KHL
LAL, LHL, Q4L
MAL, MHL,MEL, MXL
Alternate Mounting Kit
Channel/Flange Support Kit
Auxiliary Lock Plate
Special Lugs for
Disconnect Switches
Operating Rods
Disconnect
Device
© 1997 Square D All Rights Reserved
Permits mounting Class 9422 Type A1 or A2 handle mechanisms in
enclosures with flange thickness of 16 gauge to 0.5 inch.
Auxiliary kit recommended for use with 30 and 60 Ampere disconnect
switches and FAL, FCL, FHL, KAL, and KHL circuit breaker mechanisms
when these devices are to be mounted on the center channel of a multi-
door enclosure or when extra rigidity for the flange is required. Supplied as
standard with 100 and 200 ampere disconnect switches and LAL, LHL,
Q4L, MAL, MHL, MEL, and MXL circuit breaker mechanisms
Auxiliary kit recommended for use with the Class 9422 Type A-1 flange
handle to facilitate padlocking the handle in the OFF position. Primarily
used when the handle is mounted on the center channel of a multi-door
enclosure. Also in any case where the enclosure doors interfere with the
normal padlock slot in the flange handle. Meets both the Automotive and
NFPA 79 specifications.
Copper lugs only – specify Form Y157
Tin-plated aluminum lugs for 400A Type TG switch – specify Form Y1572
(000-750 Kcmil Cu/Al wire)
Anderson Type VCEL compression lugs – specify Form Y1574.
Exceptions: all 30A and 60A disconnect switches are not available with
compression lugs
Standard operating rod for use with Class 9422 variable depth mecha-
nisms. Included as standard in each kit
Extra long operating rod for use with Class 9422 variable depth mecha-
nisms. Can be used as a substitute for the standard rod included in each
kit to increase the maximum mounting depth 7''. (Two are required for
Types ARR, RR, ART, RT, ATE, TE, ATF, TF)
Minimum
Minimum
11.37
11.37
11.37
13.13
10.50
10.66
11.13
12.13
13.75
Description
Mounting Depth
Enclosure
Maximum
Maximum
19.25
19.25
19.25
20.81
19.50
19.50
19.50
19.88
20.25
Class
9422
9422
9422
9422
9422
—
—
Type
D2
12/97
Type
AM2
C1
R1
R2
—
—
L1