T4810000 Red Lion Controls, T4810000 Datasheet - Page 6

• Manufacturer Part Number: T4810000
• Description: Process/Temperature Controller
• Manufacturer: Red Lion Controls
• Type: Temperaturer

Specifications of T4810000

• Operating Temperature Max: 50°C
• Operating Temperature Min: 0°C
• Temperature Accuracy ±: 0.3%
• Output Voltage Max: 250VAC
• Output Voltage Min: 30VDC
• Controller Input: Thermocouple Or RTD
• Brand/series: T48 Series
• Contact Form: SPST
• Current, Load: 1 A @ 35 °C (Max.)
• Dimensions: 49.5mmW×49.5mmH×115.3mmD
• Enclosure Rating: IP65
• Input Type: RTD/Thermocouple
• Ip Rating: IP65
• Memory: EEPROM
• Mounting Type: Panel
• Output Type: Relay
• Power, Rating: 8 VA
• Primary Type: Controller
• Special Features: EEPROM
• Standards: cURus, CE
• Temperature, Ambient: 0 to +50 °C (Max.)
• Termination: Screw
• Voltage, Rating: 120⁄240 VAC
• Voltage, Supply: 85 to 250 VAC
• Panel Cutout: 1.77" × 1.77" (1⁄16 DIN)
• Power Requirements: 85-250 VAC
• Sealing: NEMA 4X/IP65
• Operating Temperature: 0°C to +50°C
• Thermocouple Type: J, K, T, E, R, S, B, N, Linear MV
• Rohs Compliant: NA
• Lead Free Status / RoHS Status: na

MULTIPLE UNIT STACKING
stacked either horizontally or vertically. For vertical stacking, install the panel
latch with the screws to the sides of the unit. For horizontal stacking, the panel
latch screws should be at the top and bottom of the unit. The minimum spacing
from center line to center line of units is 1.96" (49.8 mm). This spacing is the
same for vertical or horizontal stacking.
Note: When stacking units, provide adequate panel ventilation to ensure that
ACCESSORY - CURRENT TRANSFORMER-50 A
equipped with the Heater Current Monitor.
PANEL LATCH INSTALLED FOR
The T48 is designed for close spacing of multiple units. Units can be
the maximum operating temperature range is not exceeded.
The external Current Transformer is used when specifying the T48s
Part Number: CT005001
Current Ratio: 50 : 0.1 (Amperes)
Operation Frequency: 50 to 400 Hz
Insulation Class: 0.6 KV BIL, 10 KV full wave.
Terminals: Brass studs No. 8-32 UNC with flat washer and hex nuts.
Window Diameter: 1.13" (28.7 mm)
Weight: 8 oz (226.0 g)
VERTICAL UNIT STACKING
PANEL CUT-OUT SPACING FOR MULTIPLE UNIT STACKING.
HORIZONTAL ARRANGEMENT SHOWN.
PANEL LATCH INSTALLED FOR
HORIZONTAL UNIT STACKING
6
ACCESSORY - EXTERNAL SSR POWER UNIT
Drive outputs to switch loads up to 240 VAC @ 45 Amps, 25°C ambient. The
unit is operated by applying a low level DC control signal to the isolated
input. The unit features zero cross detection circuits which reduces radiated
RFI when switching load currents. With no contacts to wear out, the SSR
Power Unit provides virtually limitless operational life. The unit is supplied
with an integral heat sink for immediate installation.
External SSR Power Unit:
ACCESSORY - CURRENT TRANSFORMER-40 A
equipped with the Heater Current Monitor.
Current Transformers:
The external SSR Power Unit is used with T48s equipped with Logic/SSR
Part Number: RLY50000
Switched Voltage Range: 50 to 280 VAC
Load Current: 45 Amps max. @ 25°C ambient temperature
On State Input: 3 to 32 VDC @ 1500 Ω impedance. (isolated)
Off State Input: 0.0 to 1.0 VDC
Size: 5.5" (14 cm) L x 4.75" (12 cm) W x 2.62" (6.6 cm) H
The external Current Transformer is used when specifying the T48s
Part Number: CT004001
Current Ratio: 40 : 0.1 (Amperes)
Max Heater Current: 50 A
Dielectric Strength: 1000 VAC (For 1 minute)
Vibration Resistance: 50 Hz (Approx 10 G)
Terminals: Solder Type
Window Diameter: 0.228" (5.8 mm)
Weight: 0.406 oz (11.5 g)
35 Amps max. @ 50°C ambient temperature
(Use Logic/SSR drive output.)