CS1W-CN713 Omron, CS1W-CN713 Datasheet - Page 138
CS1W-CN713
Manufacturer Part Number
CS1W-CN713
Description
"CABLE CS1 EXP I/O,70cm"
Manufacturer
Omron
Datasheet
1.CS1W-CN313.pdf
(152 pages)
Specifications of CS1W-CN713
Lead Free Status / Rohs Status
Lead free / RoHS Compliant
- Current page: 138 of 152
- Download datasheet (3Mb)
Terminal Blocks
116
Wiring and Connections
CQM1-PA203
CQM1-PA216
AC
input
LG
GR
AC
input
Note
Note Always use crimp connectors for wiring. Do not connect bare stranded wires
Use an AC power supply
between 100 and 240 V AC.
Noise filter neutral terminal
(see note 4)
Protective earth terminal
(see note 5)
Use an AC power supply
of 100 or 230 V AC.
Voltage selector (see note 6)
Short: 100 V AC
Open: 230 V AC
Protective earth terminal
(see note 5)
Use the 24 V DC, 0.5 A
terminals to supply power
to DC Input Units.
directly to terminals.
The following diagram shows the terminal blocks for the AC Power Supply
Units.
1. The wire used should be at least 2 mm
2. Provide the grounding point as close to the CQM1H PC as possible.
3. Tighten the terminal screws to a torque of 0.8 N • m.
4. LG (
5. GR (
6. When supplying voltage at 100 V AC with the CQM1-PA216, the voltage
Noise filter neutral terminal. Short-circuit the LG (
GR (
tance of less than 100
Protective earth terminal. Connect to a separate ground wire of at least
2 mm
electric shock.
selector terminals must be shorted, and when supplying voltage at 230 V
AC the must be open. When power is supplied at 230 V AC using the
CQM1-PA216, remove the short-circuit bar (provided as an accessory)
that shorts the voltage selector terminals. The Unit will be damaged if
230 V AC is supplied with the short-circuit bar connected.
2
to ground the terminal at a resistance of less than 100
or
) terminals using the short-circuit bar and ground them at a resis-
):
):
7 mm max.
to reduce noise and prevent electric shock.
CQM1-PA206
2
.
AC
input
LG
GR
Use an AC power supply
between 100 and 240 V AC.
Noise filter neutral terminal
(see note 4)
Protective earth terminal
(see note 5)
Use the 24 V DC, 0.5 A ter-
minals to supply power to
DC Input Units.
or
Section 4-7
) terminal and
to prevent
Related parts for CS1W-CN713
Image
Part Number
Description
Manufacturer
Datasheet
Request
R
Part Number:
Description:
MODULE,ANALOG OUT,4CH
Manufacturer:
Omron
Datasheet:
Part Number:
Description:
MODULE, ANALOG IN, 8CH
Manufacturer:
Omron
Datasheet:
Part Number:
Description:
Connector Cable
Manufacturer:
Omron
Datasheet:
Part Number:
Description:
Cable Connector
Manufacturer:
Omron
Datasheet:
Part Number:
Description:
"BATTERY,CPU,CS1 SERIES ONLY"
Manufacturer:
Omron
Datasheet:
Part Number:
Description:
"CABLE,CS1/ CQM1-PRO01,0.1m"
Manufacturer:
Omron
Datasheet:
Part Number:
Description:
BACKPLANE,CS1 CPU,3 SLOTS
Manufacturer:
Omron
Datasheet:
Part Number:
Description:
"BACKPLANE,CS1 CPU,8 SLOTS"
Manufacturer:
Omron
Datasheet:
Part Number:
Description:
G6S-2GLow Signal Relay
Manufacturer:
Omron Corporation
Datasheet:
Part Number:
Description:
Compact, Low-cost, SSR Switching 5 to 20 A
Manufacturer:
Omron Corporation
Datasheet:
Part Number:
Description:
Manufacturer:
Omron Corporation
Datasheet: