S1D15206F00A200 Epson, S1D15206F00A200 Datasheet - Page 578
S1D15206F00A200
Manufacturer Part Number
S1D15206F00A200
Description
LCD Drivers LCD DRIVER
Manufacturer
Epson
Datasheet
1.S1D15206F00A200.pdf
(612 pages)
Specifications of S1D15206F00A200
Lead Free Status / RoHS Status
Lead free / RoHS Compliant
Available stocks
Company
Part Number
Manufacturer
Quantity
Price
Part Number:
S1D15206F00A200
Manufacturer:
EPSON/爱普生
Quantity:
20 000
- Current page: 578 of 612
- Download datasheet (5Mb)
Reset Circuit
When RES pin goes low,or when Reset command is
used,this LSI is initialized.
Initialized states :
*
*
Rev. 1.1a
1
2
• Serial interface internal shift register and counter
• Power saver mode is entered.
• Display normal
• Page address=0H
• Column address=00H
• Display start line address=00H
• Segment driver direction = normal
• Common driver direction = normal
• Read modify write OFF
• Power control register (D2, D1, D0) = (0, 0, 0)
This faculty is available only S1D15B01D00B
This faculty is not available by reset command, it is abailable only when hard reset : RES=LOW is active.
clear
• Oscillation circuit is stopped.
• The LCD power supply circuit is stopped.
• Display OFF
• Display all points ON
• Segment/common driver outputs go to the V
level.
*
.
SS
EPSON
When reset is detected, this LSI is set to above initialized
states. However it has no effect on contents of DDRAM.
As seen in “Microprocessor Interface (Reference
Example)”, connect RES pin to the reset pin of the MPU
and initialize the MPU at the same time. The initialization
by RES pin is always required during power-on.
If the control signal from MPU is HZ, an overcurrent
may flow through the LSI. A protection is required to
prevent the HZ signal at the input pin during power-on.
In case the S1D15B01 series does not use the on-chip
LCD power supply circuit, RES pin must be HIGH
when the external LCD power supply is turned on.
• V
• Electronic volume register (D4, D3, D2, D1, D0) =
• LCD power supply bias ratio = 1/7 bias
• Test mode is released.
• V
• V
(1, 0, 0, 0, 0)
0
0
OUT
-resistor ratio register (D2, D1, D0) = (0, 0, 0)
is shorted to V
is shorted to V
SS
*
DD2
1
*
1
*
S1D15B01 Series
2
13–23
Related parts for S1D15206F00A200
Image
Part Number
Description
Manufacturer
Datasheet
Request
R
Part Number:
Description:
INK CARTRIDGE, T0803, EPSON, MAG
Manufacturer:
Epson
Datasheet:
Part Number:
Description:
INK CARTRIDGE, T0804, EPSON, YEL
Manufacturer:
Epson
Datasheet:
Part Number:
Description:
INK CARTRIDGE, LT, EPSON, CYAN
Manufacturer:
Epson
Datasheet:
Part Number:
Description:
CXA1034M
Manufacturer:
EPSON Electronics
Datasheet:
Part Number:
Description:
Manufacturer:
EPSON Electronics
Datasheet:
Part Number:
Description:
Manufacturer:
EPSON Electronics
Datasheet:
Part Number:
Description:
Manufacturer:
EPSON Electronics
Datasheet:
Part Number:
Description:
Manufacturer:
EPSON Electronics
Datasheet:
Part Number:
Description:
RTC58321Real time clock module(4-bit I/O CONNECTION REAL TIME CLOCK MODULE)
Manufacturer:
EPSON Electronics
Datasheet:
Part Number:
Description:
SCI7661DC-DC Converter
Manufacturer:
EPSON Electronics
Datasheet:
Part Number:
Description:
Manufacturer:
EPSON Electronics
Datasheet:
Part Number:
Description:
Manufacturer:
EPSON Electronics
Datasheet: