GRM3195C1H682JA01D Murata, GRM3195C1H682JA01D Datasheet - Page 11

• Manufacturer Part Number: GRM3195C1H682JA01D
• Description: CAPACITOR, 1206 6.8NF 50V CAPACITOR, 1206 6.8NF 50V
• Manufacturer: Murata
• Series: GRM31r

Specifications of GRM3195C1H682JA01D

• Tolerance (+ Or -): 5%
• Voltage: 50VDC
• Temp Coeff (dielectric): C0G
• Operating Temp Range: -55C to 125C
• Mounting Style: Surface Mount
• Construction: SMT Chip
• Case Style: Ceramic Chip
• Failure Rate: Not Required
• Wire Form: Not Required
• Product Length (mm): 3.2mm
• Product Depth (mm): 1.6mm
• Product Height (mm): 0.85mm
• Product Diameter (mm): Not Requiredmm
• Capacitance: 6800pF
• Package / Case: 1206
• Voltage Rating, Dc: 50V
• Capacitor Dielectric Type: CERAMIC MULTI-LAYER
• Tolerance,: 5%
• Tolerance, -: 5%
• Temp, Op. Max: 125(DEGREE C)
• Temp, Op.: ROHS COMPLIANT
• Tolerance: 5 %
• Voltage Rating: 50 Volts
• Operating Temperature Range: - 55 C to + 125 C
• Temperature Coefficient / Code: C0G (NP0)
• Product: General Type MLCCs
• Dimensions: 1.6 mm W x 3.2 mm L x 0.85 mm H
• Termination Style: SMD/SMT
• Lead Free Status / RoHS Status: Compliant

4
!Note
!Note
24
No.
13
14
15
GRM Series Specifications and Test Methods
Continued from the preceding page.
Resistance
to
Soldering
Heat
Solderability of
Termination
Temperature
Cycle
• Please read rating and !CAUTION (for storage, operating, rating, soldering, mounting and handling) in this catalog to prevent smoking and/or burning, etc.
• This catalog has only typical specifications because there is no space for detailed specifications. Therefore, please approve our product specifications or transact the approval sheet for product specifications before ordering.
Please read rating and !CAUTION (for storage, operating, rating, soldering, mounting and handling) in this PDF catalog to prevent smoking and/or burning, etc.
This catalog has only typical specifications. Therefore, you are requested to approve our product specifications or to transact the approval sheet for product specificaions before ordering.
Item
Appearance
Capacitance
Change
Q/D.F.
I.R.
Dielectric
Strength
Appearance
Capacitance
Change
Q/D.F.
I.R.
Dielectric
Strength
75% of the terminations are to be soldered evenly and
continuously.
The measured and observed characteristics should satisfy the
specifications in the following table.
No marking defects
Within T2.5% or T0.25pF
(Whichever is larger)
30pFmin. : Q U1000
30pFmax. : Q U400W20C
C : Nominal Capacitance (pF)
More than 10,000MΩ or 500Ω • F (Whichever is smaller)
No failure
The measured and observed characteristics should satisfy the
specifications in the following table.
No marking defects
Within T2.5% or T0.25pF
(Whichever is larger)
30pFmin. : Q U1000
30pFmax. : Q U400W20C
C : Nominal Capacitance (pF)
More than 10,000MΩ or 500Ω • F (Whichever is smaller)
No failure
Compensating Type
Temperature
Specifications
R6, R7 : Within T7.5%
E4, F5 : Within T20%
[R6, R7]
W.V. : 25Vmin. : 0.025max.
W.V. : 16/10V : 0.035max.
W.V. : 6.3V :
[E4]
W.V. : 25Vmin. : 0.025max.
[F5]
W.V. : 25Vmin.
W.V. : 16V/10V : 0.125max.
W.V. : 6.3Vmax. : 0.15max.
R6, R7 : Within T7.5%
E4, F5 : Within T20%
[R6, R7]
W.V. : 25Vmin. : 0.025max.
W.V. : 16/10V : 0.035max.
W.V. : 6.3V
[E4]
W.V. : 25Vmin. : 0.025max.
[F5]
W.V. : 25Vmin.
W.V. : 16V/10V : 0.125max.
W.V. : 6.3Vmax. : 0.15max.
High Dielectric Type
0.05max. (CF3.3µF)
0.1max. (C U3.3µF)
0.05max. (CF3.3µF)
0.1max. (C U3.3µF)
: 0.05max. (CF0.10µF)
: 0.09max. (C U0.10µF)
: 0.05max. (CF0.10µF)
: 0.09max. (C U0.10µF)
Immerse the capacitor in a solution of ethanol (JIS-K-8101) and
rosin (JIS-K-5902) (25% rosin in weight proportion).
Preheat at 80 to 120D for 10 to 30 seconds. After preheating,
immerse in eutectic solder solution for 2T0.5 seconds at
230T5D.
Preheat the capacitor at 120 to 150D for 1 minute.
Immerse the capacitor in a eutectic solder solution at 270T5D
for 10T0.5 seconds. Let sit at room temperature for 24T2 hours
(temperature compensating type) or 48T4 hours (high dielectric
constant type), then measure.
#Initial measurement for high dielectric constant type
Perform a heat treatment at 150
let sit for 48T4 hours at room temperature.
Perform the initial measurement.
*Preheating for GRM32/43/55
Fix the capacitor to the supporting jig in the same manner and
under the same conditions as (10). Perform the five cycles
according to the four heat treatments listed in the following
table. Let sit for 24T2 hours (temperature compensating type)
or 48T4 hour (high dielectric constant type) at room
temperature, then measure.
#Initial measurement for high dielectric constant type
Perform a heat treatment at 150
let sit for 48T4 hours at room temperature.
Perform the initial measurement.
Temp. (D)
Time (min.)
Step
Step
1
2
Temp.W0/Y3
Operating
30T3
Min.
100D to 120D
170D to 200D
Temperature
1
Test Method
Temp.
Room
2 to 3
Continued on the following page.
Y10
Y10
W
W
2
0
0
D for one hour and then
D for one hour and then
Temp.W3/Y0
Operating
30T3
Max.
C02E10.pdf 04.1.20
3
1 min.
1 min.
Time
Temp.
Room
2 to 3
4