AD8306AR Analog Devices Inc, AD8306AR Datasheet
AD8306AR
Specifications of AD8306AR
Available stocks
Related parts for AD8306AR
AD8306AR Summary of contents
Page 1
FEATURES Complete, Fully Calibrated Log-Limiting IF Amplifier 100 dB Dynamic Range: –91 dBV to +9 dBV Stable RSSI Scaling Over Temperature and Supplies: 20 mV/dB Slope, –95 dBm Intercept 0.4 dB RSSI Linearity up to 200 MHz Programmable Limiter ...
Page 2
AD8306–SPECIFICATIONS Parameter Conditions INPUT STAGE (Inputs INHI, INLO) 2 Maximum Input Differential Drive, p-p Equivalent Power in 50 Terminated in 52.3 Noise Floor Terminated 50 Equivalent Power in 50 400 MHz Bandwidth Input Resistance From INHI to INLO Input Capacitance ...
Page 3
... Maximum Junction Temperature . . . . . . . . . . . . . . . . +125 C Operating Temperature Range . . . . . . . . . . . . – +85 C Temperature Model Range AD8306AR – +85 C AD8306AR-REEL – +85 C AD8306AR-REEL7 – +85 C AD8306ACHIPS – +85 C 5962-9864601QEA – +125 C AD8306-EVAL CAUTION ESD (electrostatic discharge) sensitive device. Electrostatic charges as high as 4000 V readily accumulate on the human body and test equipment and can discharge without detection. ...
Page 4
AD8306 –Typical Performance Characteristics 100 + 0 + 0.01 0.001 0.0001 0.00001 0.5 0.7 0.9 1.1 1.3 1.5 ENABLE VOLTAGE – V Figure 1. Supply Current vs. Enable Voltage @ ...
Page 5
– + –120 –100 –80 –60 –40 (–87dBm) INPUT LEVEL – dBV Figure 7. RSSI Output vs. Input Level, 100 MHz ...
Page 6
AD8306 100 200 FREQUENCY – MHz Figure 13. RSSI Slope vs. Frequency Using Termination of 52.3 0.4 0.375 0.35 0.325 0.3 0.275 0. 100 150 200 250 FREQUENCY – MHz Figure 14. ...
Page 7
PRODUCT OVERVIEW The AD8306 is built on an advanced dielectrically-isolated complementary bipolar process using thin-film resistor technol- ogy for accurate scaling. It follows well-developed foundations proven over a period of some fifteen years, with constant refine- ment. The backbone of ...
Page 8
AD8306 voltage sensitivity. Most interfaces have additional small junc- tion capacitances associated with them, due to active devices or ESD protection; these may be neither accurate nor stable. Component numbering in each of these interface diagrams is local. Enable Interface ...
Page 9
RSSI output voltage for zero input, and to provide temperature compensation, resulting in a stable intercept. For zero signal conditions, all the detector output currents are equal. For a finite input, of ...
Page 10
AD8306 low frequency applications, a simple RC network forming a low- pass filter should be added at the input for the same reason. If the limiter output is not required, Pin 9 (LMDR) should be left open and Pins 12 ...
Page 11
COM2 VLOG 0 VPS1 VPS2 C1 3 PADL PADL 0.01 F AD8306 4 INHI LMHI SIGNAL R T INPUTS 52.3 5 INLO LMLO C2 6 0.01 F PADL PADL 7 COM1 FLTR ENBL 8 LMDR ...
Page 12
AD8306 Table I. Match to 50 (Gain = 13 dB MHz 140 3500 10.7 133 3200 15 95.0 2250 20 71.0 1660 21.4 66.5 1550 25 57.0 1310 30 47.5 1070 ...
Page 13
The AD8031 rail-to-rail op amp, used in both ex- amples, can swing from 4. single +5 V supply. If high output current is required (> 10 mA), the AD8051, which also has ...
Page 14
AD8306 0 SIG 0.01 F INHI R10 52.3 SIG C2 INLO R1 0. EXT ENABLE Component Function SW1 Device Enable. When in Position A, the ENBL pin is connected to +V ...
Page 15
Figure 34. Layout of Signal Layer Figure 35. Layout of Power Layer REV. A Figure 36. Signal Layer Silkscreen Figure 37. Power Layer Silkscreen –15– AD8306 ...
Page 16
AD8306 0.1574 (4.00) 0.1497 (3.80) OUTLINE DIMENSIONS Dimensions shown in inches and (mm). 16-Lead Narrow Body SO (SO-16) 0.3937 (10.00) 0.3859 (9.80 0.2440 (6.20) 0.2284 (5.80 PIN 1 0.0688 (1.75) 0.050 (1.27) BSC 0.0532 (1.35) 0.0098 ...