CY8C3866LTI-023 Cypress Semiconductor Corp, CY8C3866LTI-023 Datasheet - Page 25

• Manufacturer Part Number: CY8C3866LTI-023
• Description: CY8C3866LTI-023
• Manufacturer: Cypress Semiconductor Corp
• Series: PSOC™ 3 CY8C38xxr

Specifications of CY8C3866LTI-023

• Core Processor: 8051
• Core Size: 8-Bit
• Speed: 67MHz
• Connectivity: EBI/EMI, I²C, LIN, SPI, UART/USART, USB
• Peripherals: CapSense, DMA, POR, PWM, WDT
• Number Of I /o: 38
• Program Memory Size: 64KB (64K x 8)
• Program Memory Type: FLASH
• Eeprom Size: 2K x 8
• Ram Size: 8K x 8
• Voltage - Supply (vcc/vdd): 1.71 V ~ 5.5 V
• Data Converters: A/D 2x20b, D/A 4x8b
• Oscillator Type: Internal
• Operating Temperature: -40°C ~ 85°C
• Package / Case: *
• Lead Free Status / RoHS Status: Lead free / RoHS Compliant

The extended data pointer SFRs, DPX0, DPX1, MXAX, and
P2AX, hold the most significant parts of memory addresses
during access to the xdata space. These SFRs are used only
with the MOVX instructions.
During a MOVX instruction using the DPTR0/DPTR1 register,
the most significant byte of the address is always equal to the
contents of DPX0/DPX1.
During a MOVX instruction using the R0 or R1 register, the most
significant byte of the address is always equal to the contents of
MXAX, and the next most significant byte is always equal to the
contents of P2AX.
I/O Port SFRs
The I/O ports provide digital input sensing, output drive, pin
interrupts, connectivity for analog inputs and outputs, LCD, and
access to peripherals through the DSI. Full information on I/O
ports is found in
I/O ports are linked to the CPU through the PHUB and are also
available in the SFRs. Using the SFRs allows faster access to a
limited set of I/O port registers, while using the PHUB allows boot
configuration and access to all I/O port registers.
Each SFR supported I/O port provides three SFRs:
Document Number: 001-11729 Rev. *R
INC DPTR
MOV DPTR, #data16
SFRPRTxDR sets the output data state of the port (where × is
port number and includes ports 0–6, 12 and 15).
The SFRPRTxSEL selects whether the PHUB PRTxDR
register or the SFRPRTxDR controls each pin’s output buffer
within the port. If a SFRPRTxSEL[y] bit is high, the
corresponding SFRPRTxDR[y] bit sets the output state for that
pin. If a SFRPRTxSEL[y] bit is low, the corresponding
PRTxDR[y] bit sets the output state of the pin (where y varies
from 0 to 7).
The SFRPRTxPS is a read only register that contains pin state
values of the port pins.
I/O System and Routing
on page 33.
5.7.3.1 xdata Space
The 8051 xdata space is 24-bit, or 16 MB in size. The majority of
this space is not ‘external’—it is used by on-chip components.
See
accessed using the EMIF. See
page 23.
Table 5-5. XDATA Data Address Map
0×00 0000 – 0×00 1FFF
0×00 4000 – 0×00 42FF
0×00 4300 – 0×00 43FF
0×00 4400 – 0×00 44FF
0×00 4500 – 0×00 45FF
0×00 4700 – 0×00 47FF
0×00 4900 – 0×00 49FF
0×00 4E00 – 0×00 4EFF
0×00 4F00 – 0×00 4FFF
0×00 5000 – 0×00 51FF
0×00 5400 – 0×00 54FF
0×00 5800 – 0×00 5FFF
0×00 6000 – 0×00 60FF
0×00 6400 – 0×00 6FFF
0×00 7000 – 0×00 7FFF
0×00 8000 – 0×00 8FFF
0×00 A000 – 0×00 A400
0×00 C000 – 0×00 C800
0×01 0000 – 0×01 FFFF
0×05 0220 – 0×05 02F0
0×08 0000 – 0×08 1FFF
0×80 0000 – 0×FF FFFF
Table
Address Range
5-5. External, that is, off-chip, memory can be
PSoC
SRAM
Clocking, PLLs, and oscillators
Power management
Interrupt controller
Ports interrupt control
Flash programming interface
I
Decimator
Fixed timer/counter/PWMs
I/O ports control
EMIF control registers
Analog subsystem interface
USB controller
UDB configuration
PHUB configuration
EEPROM
CAN
DFB
Digital Interconnect
configuration
Debug controller
Flash ECC bytes
External memory interface
®
2
External Memory Interface
C controller
3: CY8C38 Family
Purpose
Data Sheet
Page 25 of 129
on
[+] Feedback