G3RD-X02PN DC24 Omron, G3RD-X02PN DC24 Datasheet - Page 23

• Manufacturer Part Number: G3RD-X02PN DC24
• Description: OUTPUT MODULE
• Manufacturer: Omron
• Series: G3RDr

Specifications of G3RD-X02PN DC24

• Circuit: SPST-NO (1 Form A)
• Output Type: DC
• Load Current: 2A
• Voltage - Input: 19.2 ~ 28.8VDC
• Voltage - Load: 3 ~ 52.8 V
• Mounting Type: Through Hole
• Termination Style: PC Pin
• Package / Case: Module
• Lead Free Status / RoHS Status: Lead free / RoHS Compliant
• On-state Resistance: -
• Lead Free Status / Rohs Status: Lead free / RoHS Compliant
• Other names: G3RD-X02PNDC24; G3RDX02PNDC24; G3RDX02PNDC24NC

Tightening
The suitable tightening torque for screw terminals is given below.
Operation
1. If the switching speed is extremely slow, the contacts may not be
2. If the switching speed is extremely fast, switching shock may
Panel Mount Switch (Z-15@Q@, Z-01@Q@)
High-sensitivity Switch (Z-15H)/
Extra-high-sensitivity Switch (Z-15H2)
• Make sure that the switching speed and frequency are is within the
• Make sure that the actuator travel does not exceed the permissible
• When mounting the panel mount plunger model with screws on a
• When using the panel mount plunger model mounted with screws
• When using the panel mount plunger model mounted with screws
• When using the Switch in a DC circuit, be sure to provide an arc
• In an application where a high repeat accuracy is required, limit the
• Do not apply a force of 19.6 N or higher to the pin plunger.
• Exercise care that the environment conditions such as temperature
specified ranges.
OT position. The operating stroke must be set to 70% to 100% of
the rated OT.
side surface, be careful of the dog angle and operation speed.
Excessive dog angle or operation speed may damage the Switch.
on a side surface, be careful not to apply a large shock. Applying a
shock exceeding 1,000 m/s
on a side surface, remove the hexagonal nuts from the actuator.
suppressor as well because the small contact gap of the Switch
may result in contact troubles.
current that flows through the Switch to within 0.1 A. Also, use a
relay to control a high-capacity load if the Switch is connected to
such a load. (In this case, the exciting current of the relay coil is the
load of the Switch.)
and humidity do not change abruptly.
Screw terminals except for those on Split-contact Models (Z-10FY-
B): 0.78 to 1.18 N·m
Screw terminals on Split-contact Models (Z-10FY-B):
0.49 to 1.18 N·m
switched smoothly, which may result in a contact failure or contact
welding.
damage the Switch prematurely. If the switching frequency is too
high, the contacts may not be able to keep up with the speed.
The rated permissible switching speed and frequency indicate the
switching reliability of the Switch.
The life of a Switch is determined at the specified switching speed.
The life varies with the switching speed and frequency even when
they are within the permissible ranges. Always conduct appropriate
durability tests under actual conditions before using a Switch.
2
may damage the Switch.
Micro Load Applicable Range
Using a model for ordinary loads to open or close the contact of a
micro load circuit may result in faulty contact. Use models that operate
in the following range. However, even when using micro load models
within the operating range shown here, if inrush current occurs when
the contact is opened or closed, it may increase contact wear and so
decrease durability. Therefore, insert a contact protection circuit
where necessary.
The minimum applicable load is the N-level reference value. This
value indicates the malfunction reference level for the reliability level
of 60% (λ 60). The equation, λ 60 = 0.5×10
the estimated malfunction rate is less than 1/2,000,000 operations
with a reliability level of 60%.
Models with Drip-proof Terminal Cover (Z-@A55-B5V)
Wiring
Rubber packing
Terminal with
toothed
washer
• To attach the Protective Cover to the case, hold the cover in almost
• Use round solderless terminals having the
• A cable 8.5 to 10.5 mm in diameter can be
• Use M4 small screws with spring toothed washer are used as the
Minimum applicable
load
parallel to the case and then push it to the case. If the cover is
pushed diagonally, the rubber packing may slip off, degrading the
sealability of the Switch.
following dimensions to connect leads to the
terminals. Tighten the screws of terminals to
a torque of 0.78 to 1.18 N·m. Use the
terminal shown below.
applicable to the sealing rubber of the lead outlet of the Switch. A
two-core or three-core VCT cable having a cross-sectional area of
1.25 mm
terminal screws.
2
is especially suitable for this.
30
24
12
5
0
0.1
Unusable
range
5 mW
0.16 mA
1 mA at 5 VDC
1 mA
1
Operating range
for micro load
models Z-01H
Z-01H
10
800 mW
26 mA
100 mA 160 mA
-6
/operations indicates that
100
Operating
range for
general load
models
Z-15H, H2
Z-15G
Z-15E
Z-10FY
Z-15ER
Current (mA)
160 mA at 5 VDC
Z-15@, Z-10FY
1,000
20 max.
4.3 dia.
Z
8
23