GNM314R71H102KD01D Murata, GNM314R71H102KD01D Datasheet - Page 214

• Manufacturer Part Number: GNM314R71H102KD01D
• Manufacturer: Murata
• Type: Ceramicr

Specifications of GNM314R71H102KD01D

• Capacitance: 1000pF
• No. Of Capacitors: 4
• Tolerance (+ Or -): 10%
• Voltage: 50VDC
• Number Of Terminals: 8Terminal
• Temp Coeff (dielectric): X7R
• Operating Temp Range: -55C to 125C
• Mounting Style: Surface Mount
• Package / Case: 1206
• Construction: SMT Chip
• Failure Rate: Not Required
• Product Height (mm): 0.8mm
• Product Depth (mm): 1.6mm
• Product Length (mm): 3.2mm
• Lead Diameter (nom): Not Requiredmm
• Terminal Pitch: 0.8mm
• Lead Free Status / RoHS Status: Compliant

18
!Note
• This PDF catalog is downloaded from the website of Murata Manufacturing co., ltd. Therefore, it’s specifications are subject to change or our products in it may be discontinued without advance notice. Please check with our
• This PDF catalog has only typical specifications because there is no space for detailed specifications. Therefore, please approve our product specifications or transact the approval sheet for product specifications before ordering.
sales representatives or product engineers before ordering.
!Note
5. Flow Soldering
Table 2
Recommended Conditions
212
!Caution
Pb-Sn Solder: Sn-37Pb
Lead Free Solder: Sn-3.0Ag-0.5Cu
Optimum Solder Amount for Flow Soldering
Peak Temperature
When sudden heat is given to the components, the
mechanical strength of the components should go down
because remarkable temperature change causes
deformity of components inside. And an excessively long
soldering time or high soldering temperature results in
leaching by the outer electrodes, causing poor adhesion
or a reduction in capacitance value due to loss of contact
between electrodes and end termination.
In order to prevent mechanical damage in the
components, preheating should be required for both of
the components and the PCB board. Preheating
conditions are shown in Table 2. It is required to keep
temperature differential between the soldering and the
components surface ( T) as small as possible.
When components are immersed in solvent after
mounting, be sure to maintain the temperature difference
between the component and solvent within the range
shown in Table 2.
Do not apply flow soldering to chips not listed in Table 2.
The top of the solder fillet should be lower than the
thickness of components. If the solder amount is
excessively big, the risk of cracking is higher during
board bending or under any other stressful conditions.
Continued from the preceding page.
• Please read rating and !CAUTION (for storage, operating, rating, soldering, mounting and handling) in this catalog to prevent smoking and/or burning, etc.
• This catalog has only typical specifications because there is no space for detailed specifications. Therefore, please approve our product specifications or transact the approval sheet for product specifications before ordering.
Atmosphere
G--18/21/31
Part Number
Pb-Sn Solder
240-250 C
Air
Temperature Differential
TV150D
Lead Free Solder
250-260 C
N
2
[Standard Conditions for Flow Soldering]
[Allowable Soldering Temperature and Time]
Peak Temperature
Temperature (D)
In case of repeated soldering, the accumulated
soldering time must be within the range shown above.
270
260
250
240
230


















170 C
150 C
130 C
0
















Adhesive
T
10
60-120 seconds
Preheating
20
Continued on the following page.
Soldering
5 seconds max.
Soldering Time (sec.)
30
Up to Chip Thickness
Gradual
Cooling
Time
in section
C02E.pdf
09.9.18