GNM314R71H102KD01D Murata, GNM314R71H102KD01D Datasheet - Page 57

• Manufacturer Part Number: GNM314R71H102KD01D
• Manufacturer: Murata
• Type: Ceramicr

Specifications of GNM314R71H102KD01D

• Capacitance: 1000pF
• No. Of Capacitors: 4
• Tolerance (+ Or -): 10%
• Voltage: 50VDC
• Number Of Terminals: 8Terminal
• Temp Coeff (dielectric): X7R
• Operating Temp Range: -55C to 125C
• Mounting Style: Surface Mount
• Package / Case: 1206
• Construction: SMT Chip
• Failure Rate: Not Required
• Product Height (mm): 0.8mm
• Product Depth (mm): 1.6mm
• Product Length (mm): 3.2mm
• Lead Diameter (nom): Not Requiredmm
• Terminal Pitch: 0.8mm
• Lead Free Status / RoHS Status: Compliant

!Note
• This PDF catalog is downloaded from the website of Murata Manufacturing co., ltd. Therefore, it’s specifications are subject to change or our products in it may be discontinued without advance notice. Please check with our
• This PDF catalog has only typical specifications because there is no space for detailed specifications. Therefore, please approve our product specifications or transact the approval sheet for product specifications before ordering.
sales representatives or product engineers before ordering.
!Note
No.
16
17
GRM Series Specifications and Test Methods (1) (Note1) Typical Inspection
Continued from the preceding page.
Humidity
(Steady
State)
Humidity
Load
• Please read rating and !CAUTION (for storage, operating, rating, soldering, mounting and handling) in this catalog to prevent smoking and/or burning, etc.
• This catalog has only typical specifications because there is no space for detailed specifications. Therefore, please approve our product specifications or transact the approval sheet for product specifications before ordering.
GRM Series Specifications and Test Methods (1) (Note1) Typical Inspection
Item
Appearance
Capacitance
Change
Q/D.F.
I.R.
Appearance
Capacitance
Change
Q/D.F.
I.R.
The measured and observed characteristics should satisfy the
specifications in the following table.
No defects or abnormalities
Within 5% or 0.5pF
(Whichever is larger)
30pF and over: QU350
10pF and over
30pF and below:
10pF and below:
C: Nominal Capacitance (pF)
More than 1,000M or 50 · F (Whichever is smaller)
The measured and observed characteristics should satisfy the
specifications in the following table.
No defects or abnormalities
Within 7.5% or 0.75pF
(Whichever is larger)
30pF and over: QU200
30pF and below:
C: Nominal Capacitance (pF)
More than 500M or 25 · F (Whichever is smaller)
Compensating Type
QU275+2.5C
QU200+10C
QU100+10C/3
Temperature
In case Non "*" is added in PNs table, please refer to GRM Series Specifications and Test Methods (1).
Specifications
In case "*" is added in PNs table, please refer to GRM Series Specifications and Test Methods (2).
B1, B3, R1, R6, R7, C8
F1, F5, E4: Within 30%
[R6, R7, C8]
W.V.: 100V
W.V.: 50/35/25/16/10V
W.V.: 6.3/4V
[E4]
W.V.: 25Vmin: 0.05 max.
[F1, F5]
W.V.: 25V min.
W.V.: 16/10V: 0.15 max.
W.V.: 6.3V: 0.2 max.
B1, B3, R1, R6, R7, C8
F1, F5, E4: Within 30%
[W.V.: 10V max.]
F1, F5: Within +30/–40%
[B1, B3, R6, R7, C8]
W.V.: 100V
W.V.: 50/35/25/16/10V
W.V.: 6.3/4V
[E4]
W.V.: 25Vmin: 0.05 max.
[F1, F5]
W.V.: 25V min.
W.V.: 16/10V: 0.15 max.
W.V.: 6.3V: 0.2 max.
Please refer to individual specifications (our product specifications or the approval sheet).
: 0.05 max. (CF0.068 F)
: 0.075 max. (CU0.068 F)
: 0.05 max. (CF0.068 F)
: 0.075 max. (CU0.068 F)
High Dielectric Type
: 0.05 max.
: 0.075 max. (CF3.3 F)
: 0.125 max. (CU3.3 F)
: 0.075 max. (CF0.1 F)
: 0.125 max. (CU0.1 F)
: 0.05 max.
: 0.075 max. (CF3.3 F)
: 0.125 max. (CU3.3 F)
: 0.075 max. (CF0.1 F)
: 0.125 max. (CU0.1 F)
: Within 12.5%
: Within 12.5%
(Note1) This Specifications and Test Methods indicates typical inspection.
Set the capacitor at 40 2 C and in 90 to 95% humidity for
500 12 hours.
Remove and set for 24 2 hours at room temperature, then
measure.
Apply the rated voltage at 40 2 C and 90 to 95% humidity for
500 12 hours. Remove and set for 24 2 hours at room
temperature, then measure.
The charge/discharge current is less than 50mA.
•Initial measurement for F1, F5/10V max.
Apply the rated DC voltage for 1 hour at 40 2 C.
Remove and set for 24 2 hours at room temperature.
Perform initial measurement.
Test Method
Continued on the following page.
C02E.pdf
55
09.9.18
1