XC5VLX50T-1FF665C Xilinx Inc, XC5VLX50T-1FF665C Datasheet - Page 293

• Manufacturer Part Number: XC5VLX50T-1FF665C
• Description: FPGA Virtex®-5 Family 46080 Cells 65nm (CMOS) Technology 1V 665-Pin FCBGA
• Manufacturer: Xilinx Inc
• Series: Virtex™-5 LXTr

Specifications of XC5VLX50T-1FF665C

• Package: 665FCBGA
• Family Name: Virtex®-5
• Device Logic Units: 46080
• Typical Operating Supply Voltage: 1 V
• Maximum Number Of User I/os: 360
• Ram Bits: 2211840
• Number Of Logic Elements/cells: 46080
• Number Of Labs/clbs: 3600
• Total Ram Bits: 2211840
• Number Of I /o: 360
• Voltage - Supply: 0.95 V ~ 1.05 V
• Mounting Type: Surface Mount
• Operating Temperature: 0°C ~ 85°C
• Package / Case: 665-BBGA, FCBGA
• Lead Free Status / RoHS Status: Contains lead / RoHS non-compliant
• For Use With: HW-V5-ML561-UNI-G - EVALUATION PLATFORM VIRTEX-5HW-V5-ML550-UNI-G - EVALUATION PLATFORM VIRTEX-5HW-V5-ML521-UNI-G - EVALUATION PLATFORM VIRTEX-5HW-V5GBE-DK-UNI-G - KIT DEV V5 LXT GIGABIT ETHERNET122-1508 - EVALUATION PLATFORM VIRTEX-5
• Number Of Gates: -
• Lead Free Status / RoHS Status: Contains lead / RoHS non-compliant

Virtex-5 FPGA User Guide
UG190 (v5.3) May 17, 2010
SSTL18_II_T_DCI (1.8V) Split-Thevenin Termination
Table 6-35
Table 6-35: Differential SSTL (1.8V) Class II DC Voltage Specifications
Figure 6-86
SSTL18_II_T_DCI (1.8V) with on-chip split-Thevenin termination. In this bidirectional I/O
standard, when 3-stated, the termination is invoked on the receiver and not on the driver.
Because the Thevenin termination on the I/O is disabled for a driving I/O, the line is
equivalent to the SSTL18_I termination scheme. This allows the line to be driven by the
weaker SSTL class I driver. The SSTL18_II_T_DCI standard behaves like a normal
SSTL18_II I/O in a bidirectional environment but has the advantage of lower drive
strength and lower power consumption due to the optimized termination circuit.
Notes:
1. V
2. Per EIA/JESD8-6, “The value of V
3. V
4. V
5. V
V
Input Parameters
V
V
V
V
V
Output Parameters
V
CCO
TT
IN
ID
ID
IX
OX
the use conditions specified by the user.”
IN
ID
IX
OX
(AC)
(DC)
(DC)
(AC)
(AC)
(AC) indicates the voltage where the differential input signals must cross.
(DC) specifies the allowable DC excursion of each differential input.
(DC) specifies the input differential voltage required for switching.
(AC) indicates the voltage where the differential output signals must cross.
(4)
(1)
(3)
(5)
lists the differential SSTL (1.8V) Class II DC voltage specifications.
shows a sample circuit illustrating a valid termination technique for
www.xilinx.com
REF
is to be selected by the user to provide optimum noise margin in
Specific Guidelines for I/O Supported Standards
–0.30
0.675
0.725
Min
0.25
0.50
1.7
–
V
CCO
Typ
1.8
–
–
–
–
–
× 0.5
V
V
V
CCO
CCO
CCO
1.125
1.075
Max
1.9
–
+ 0.30
+ 0.60
+ 0.60
293