8-1393792-5 TE Connectivity, 8-1393792-5 Datasheet - Page 463

• Manufacturer Part Number: 8-1393792-5
• Description: Electromechanical Relay DPDT 3A 5VDC 168Ohm Through Hole
• Manufacturer: TE Connectivity
• Type: Signal Relayr

Specifications of 8-1393792-5

• Contact Arrangement: DPDT
• Dc Coil Voltage: 5 V
• Coil Current: 29.76 mA
• Mounting: Through Hole
• Relay Construction: Non-Latching
• Coil Voltage Dc: 5V
• Contact Form: 2 Form C
• Voltage Rating (vdc): 220V
• Voltage Rating (vac): 250V
• Dropout Volt (min): 0.25VDCV
• Coil Resistance: 168Ohm
• Pick-up Voltage (max): 4VDC
• Maximum Power Rating: 60W/125VA
• Operate Time: 5ms
• Contact Current Rating: 3A
• Contact Material: AgNi/Au
• Coil Suppression Diode: No
• Push To Test Button: No
• Led Indicator: No
• Seal: Unsealed
• Product Height (mm): 11mm
• Product Depth (mm): 10mm
• Product Length (mm): 20.2mm
• Operating Temp Range: -25C to 85C
• Pin Count: 8
• Mounting Style: Through Hole
• Termination Style: PC Pin
• Package / Case: DIP
• Lead Free Status / Rohs Status: Compliant

Engineering Data
Control Voltage: 24VAC 50/60 Hz./DC
Sense-Current Range: 1.5 to 15 amps AC.
Internal Relay Contact Data:
Set Point Variation:
Time Delay:
Power Requirement: 1.7W or 1.7VA @ 24VAC.
Temperature Range: Storage: -40 C to +85 C.
Enclosure: Plastic dust cover.
Mounting: Socket. For sockets see KUP 3 pole sockets.
Weight: 3.17 oz. (90g) approximately.
Outline Dimensions
Dimensions are shown for
reference purposes only.
Sensing Modes
.515 MAX.
Overcurrent sensor – Detects a current in excess of the value determined
by the potentiometer setting. A built-in time delay, 200 ms, minimum,
allows for normal starting and surge currents. Actual time delay is
dependent upon potentiometer setting and magnitude of overcurrent. Any
overcurrent lasting longer than this causes the internal relay of the SDAS-
01 to energize. The relay will remain energized until sensor control voltage
is removed, even if the overcurrent ceases to exist.
Undercurrent sensor – Reacts to a complete loss of sense current, or any
current of less than the potentiometer setting. Upon application of sensor
control voltage, there is a nominal 350ms delay during which time power
line current must begin. This delay gives line components time to turn on.
If, at the end of the delay, sense current should decrease to less than the
potentiometer setting of the SDAS-01 and remain there for approximately
350 ms, the internal relay of the SDAS-01 will energize. It will remain
energized until either sense control current again exceeds the potentiom-
eter setting, or until sensor control voltage is removed.
.291 MIN.
(13.08)
1 Form C (SPDT) type (code X1): 5A @ 28VDC or 2.5A @ 120VAC, res.
2 Form C (DPDT) type (code Y2): 2A @ 28VDC or 1A @ 120VAC, res.
Overcurrent sensor: 200 ms, min., after beginning of overcurrent. Actual
Undercurrent sensor: 350 ms, typ.; 200 ms, min., from beginning of
(7.39)
25% over operating temperature range.
Operating: -25 C to +70 C.
delay is dependent upon potentiometer setting and
magnitude of overcurrent (see Figure 1).
undercurrent after control voltage is applied.
2.718 MAX.
(70.64)
10%.
Dimensions are in inches over
(millimeters) unless otherwise
specified.
(3.18)
.125
(7.14)
.281
.020 TYP.
(0.51)
(4.75
.187
(1.98)
.078
.002
.005)
Catalog 1308242
1
4
7
Issued 3-03
1.531 MAX.
A
(38.89)
2
5
8
B
SDAS-01
1.5 To 15 Amp AC Current Sensor
• Zero insertion loss
• Inductive coupling to power line
• Choice of modes
• Solid state sensing circuit
• 1 Form C (SPDT) or 2 Form C (DPDT) internal relay
Users should thoroughly review the technical data before selecting a product part
number. It is recommended that user also seek out the pertinent approvals files of
the agencies/laboratories and review them to ensure the product meets the
requirements for a given application.
Figure 1 – Typical Overcurrent Time Delay Curves
Overcurrent Sensors
Ordering Information –
Distributors are more likely to stock boldface items.
Undercurrent Sensors
3
6
9
Part Number
SDAS-01-7Y2S1024
SDAS-01-7X1S1024
Part Number
SDAS-01-8Y2S1024
1.0
0.1
10
x1
– Adjustable overcurrent sensor
– Adjustable undercurrent sensor
1.406 MAX.
Specifications and availability
subject to change.
(35.71)
Sense Current Greater Than Poteniometer
x10
series
Contacts
DPDT, 2A DC/1A AC
SPDT, 5A DC/2.5A AC
Contacts
DPDT, 2A DC/1A AC
Wiring Diagrams – Bottom Views
1 Form C
2
2 Form C
1
7
4
15 Amps
9 Amps
VOLTS
INPUT
or DC
2
AC
VOLTS
INPUT
or DC
AC
3 Amps
5
x100
1.5 Amps
5
3
9
6
www.tycoelectronics.com
Technical support:
Refer to inside back cover.
3
9
6
Mounting
Socket
Socket
Mounting
Socket
x1000
P&B
1307