8-1393792-8 TE Connectivity, 8-1393792-8 Datasheet - Page 346

• Manufacturer Part Number: 8-1393792-8
• Description: Electromechanical Relay DPDT 3A 12VDC 968Ohm Through Hole
• Manufacturer: TE Connectivity
• Type: Signal Relayr

Specifications of 8-1393792-8

• Contact Arrangement: DPDT
• Dc Coil Voltage: 12 V
• Coil Current: 12.4 mA
• Mounting: Through Hole

918
Ordering Information
Initial Dielectric Strength
Between non-connected terminals: 2,000V rms, 60 Hz.
Between non-connected terminals & relay yoke: 2,000V rms, 60 Hz.
Initial Insulation Resistance
Between non-connected terminals: 10 9 ohms at 500VDC.
Between non-connected terminals & relay yoke: 10 9 ohms at 500VDC.
Our authorized distributors are more likely to maintain the following items in stock for immediate delivery..
GPD
GPDN
Outline Dimensions
Coil Data
Voltage: 24, 120 & 220VAC, 60 Hz. Add series resistor for 380-440VDC;
Duty Cycle: Continuous.
Nominal Coil Power: 6VA for AC coils; 6W for DC coils.
Coil Operating Voltage
Nominal Coil Voltage 12
Minimum Pick-up
Voltage at 20°C
Minimum Pick-up
Voltage at 40°C
Maximum voltage for
continuous use
For 380VAC – Use 6800 ohms 4 watt resistor in series with 220VAC relay.
For 440VAC – Use 8200 ohms 6 watt resistor in series with 220VAC relay.
Drop-out voltage is between 10% and 40% of the nomninal voltages for both DC
and AC (For example: in a 120 VAC unit, drop-out will occur between 12 and 48
volts.) DC relays will function with unfiltered DC from a full-wave bridge rectifier.
Dimensions are shown for
reference purposes only.
1. Basic Series:
2. Coil Voltage:
3. Options:
GP = Non-latching Control Relay
A = 12VDC
B = 24VDC
C = 48VDC
D = 125VDC
F = 250VDC
N = Magnetic Blow-out Device
Q = Light to indicate coil energization (GP only. 120VAC, 125VDC, 220VAC and 250VDC voltages only.)
R = Internal diode to suppress coil de-energization transient. (GP only. When used on DC unit, relay release time increases to same value as AC unit).
12, 24, 48, 125 & 250VDC.
13.5
DC
9
9.5
There is no surge current during operation.
24
18
19
27
G = 24VAC, 60 Hz.
I = 120VAC, 60 Hz.
J = 220VAC, 60 Hz.
48
36
38
53
125
100
143
94
Dimensions are in inches over
(millimeters) unless otherwise
specified.
250
187
200
275
ML = Magnetic Latching Control Relay
24
19
20
27
AC, 50/60Hz
120
102
137
92
Typical Part No.
220
175
188
245
Catalog 1308242
Issued 3-03
Environmenal Data
Operating Temperature Range: 0°C to +60°C.
Vibration: Single axis fragility curve data are available on request at
frequencies from 5 Hz. to 33 Hz.
Shock: The relay, when kept energized by means of one of its own
contact sets, will withstand 40g shock load when operating on DC, and
150g shock load on AC.
Mechanical Data
Mounting Terminals: 16 flat base pins. Screw terminal sockets are
available.
Wire Connection: The 16 flat pins are arranged in four symmetrical rows
of four pins; the pitch in both directions being .394”. Connection may be
made to the relay by soldering. Sockets are available with screw terminals.
adjacent figure, allowing the relay to be inserted into the socket in either of
two positions. Terminals B2 and B3 are provided as extra connections for
special applications.
Weight: 10.9 oz. (308g) approximately.
Wiring Diagrams (Bottom Views)
Operate Data @ 20°C
Operate Time at Rated Voltage: Between energizing and opening of
normally closed contacts, less than 18 milliseconds on AC and less than
15 milliseconds on DC.
Release Time: Between energizing and closing of normally open
contacts, less than 35 milliseconds on AC and less than 30 milliseconds
on DC. Between de-energizing and opening of normally open contacts,
less than 70 milliseconds on AC and less than 8 milliseconds on DC.
Between de-energizing and closing of normally closed contacts, less than
85 milliseconds on AC and less than 25 milliseconds on DC.
Specifications and availability
subject to change.
➤
The internal wiring of the relay is also symmetrical as shown in the
GP
I
www.tycoelectronics.com
Technical support:
Refer to inside back cover.
AGASTAT
N