8-1393792-8 TE Connectivity, 8-1393792-8 Datasheet - Page 434

• Manufacturer Part Number: 8-1393792-8
• Description: Electromechanical Relay DPDT 3A 12VDC 968Ohm Through Hole
• Manufacturer: TE Connectivity
• Type: Signal Relayr

Specifications of 8-1393792-8

• Contact Arrangement: DPDT
• Dc Coil Voltage: 12 V
• Coil Current: 12.4 mA
• Mounting: Through Hole

1234
Timing Modes
Timing Specifications
Timing Ranges: 6 to 180 cycles; 0.1 to 3 / 0.1 to 10 / 0.33 to 10 / 1 to 30 / 4
Timing Adjustment: Knob or fixed time (internal fixed resistor) – all models;
Accuracy: Repeat Accuracy:
Reset Time: 25 ms. (minimum deenergized interval for on-delay or off-delay
Relay Operate Time: Off-Delay mode only: 35 ms.
Relay Release Time: On-Delay mode only: 20 ms.
Contact Data @ 25 C
Arrangements: 2 Form C (DPDT).
Rating: 10A @ 28VDC or 120VAC, resistive; 1/3 HP @ 120/240VAC.
Expected Mechanical Life: 10 million operations.
Expected Electrical Life: 500,000 operations, min., at rated resistive load.
Initial Dielectric Strength
Between Terminals and Case: 1,000VAC plus twice the nominal voltage
Outline Dimensions
Wiring Diagrams (Bottom Views)
On-Delay, Off-Delay and Interval.
Dimensions are shown for
reference purposes only.
Fixed or Knob
Off-Delay
Adjust
Overall Accuracy:
models, or minimum required closure interval for interval
models without affecting accuracy.)
1.97
(50)
to 120 sec.; 0.33 to 10 / 1 to 30 / 2 to 60 min.; 0.33 to 10
hr. (All are +10%, –1% of maximum values).
customer supplied external potentiometer or resistor
– On-Delay and Interval models only.
1.97
(50)
On-Delay & Interval
(18)
Fixed or Knob
.70
operating temperature and voltage.
and voltage ranges.
for one minute.
Adjust
1% 0.004 sec. at any combination of
5.25% throughout operating temperature
conductor cable similar
to Belden 8719, 8720 or
8769 required for leads
longer than 6 inches.
Max. permissble length
is 50 feet.
Insulated, shielded two-
3.25
(83)
Dimensions are in inches over
(millimeters) unless otherwise
specified.
External Potentiomer
On-Delay & Interval
or Resistor Adjust
Catalog 1308242
Issued 3-03
SSC
Specification Grade Discrete Plug-in
Time Delay Relay
• On-Delay, Off-Delay and Interval timing modes
• 13 timing ranges from 0.1 sec. to 60 min.
• 10A DPDT output contacts
• Escellent repeatability of 1% or better.
• Exceptional immunity to transients and noise.
• Wide operating temperature range.
Users should thoroughly review the technical data before selecting a product part
number. It is recommended that user also seek out the pertinent approvals files of
the agencies/laboratories and review them to ensure the product meets the
requirements for a given application.
Input Data @ 25 C
Voltage: See Ordering Information section for details.
Power Requirement: 3W, max.
Transient Protection: Non-repetitive transients of the following magni-
tudes will not cause spurious operation of affect function and accuracy.
Environmental Data
Temperature Range: Storage: -40 C to +85 C.
Mechanical Data
Mounting/Termination: 8- or 11-pin octal type plug. 8-pin types fit either
27E122 or 27E891, while 11-pin types fit 27E123 or 27E892.
Weight: 4 oz. (112g) approximately.
Ordering Information
Authorized distributors are likely to stock the following:
SSC12AAA
SSC12ABA
Series SSC
Industrial
Discrete
SSC
Timer
|
File 3520
File LR29186
Specifications and availability
subject to change.
01 = On-Delay
02 = Off-Delay
03 = Interval
Operating Mode
* Minimum source impedance of 100 ohm.
Operating Voltage
series
120 VAC/VDC
01
48 VAC/VDC
24VAC/VDC
|
|
|
|
|
240VAC
12VDC
2 = DPDT Relay
SSC12ACA
SSC12ADA
Operating: -30 C to +65 C.
Output
2
|
A = 120VAC, 50/60 Hz.
B = 240VAC, 50/60 Hz.
E = 24VAC, 50/60 Hz. /
F = 48VAC, 50/60 Hz. /
Q = 12VDC ( 10%)
Operating Voltage
/ 120VDC
24VDC
48VDC
(+10%, –15%)
<0.1 ms
1,000V
1,000V
1,000V
3,000V
3,000V
A
|
|
|
|
|
|
|
|
|
|
|
|
SSC12AGA
SSC12ALA.
A =0 .1 to 3 sec.
B = 0.5 to 15 sec.
C = 1 to 30 sec.
D = 2 to 60 sec.
E = 4 to 120 sec.
F = 6 to 180 sec.
G = 10 to 300 sec.
I = 2 to 60 min.
K = 3 to 180 cycles
L = 0.33 to 10 min.
M = 0.5 to 15 min.
N = 1 to 30 min.
P = 0.1 to 10 min.
Timing Range
2,500V*
2,500V*
<1 ms
240V*
240V*
480V*
A
|
A = Knob Adjust
B = External
F = Fixed Times –
www.tycoelectronics.com
Technical support:
Refer to inside back cover.
Timing Adjustment
Potentiometer or
resistor (Operating
modes 1 and 3 only).
Specify time delay
in seconds per the
following examples:
F9.000 = 9 sec.
F99.00 = 99 sec.
F999.0 = 9999 sec.
F1000 = 1000 sec.
AGASTAT
A
|
|
|
|
|
|
|
|
|
|
|
|