PIC24F16KA302T-I/SS Microchip Technology, PIC24F16KA302T-I/SS Datasheet - Page 74

• Manufacturer Part Number: PIC24F16KA302T-I/SS
• Description: 16KB Flash, 2KB RAM, 512B EEPROM, 16 MIPS, 12-bit ADC, CTMU, XLP 28 SSOP .209in
• Manufacturer: Microchip Technology
• Series: PIC® XLP™ 24Fr

Specifications of PIC24F16KA302T-I/SS

• Core Processor: PIC
• Core Size: 16-Bit
• Speed: 32MHz
• Connectivity: I²C, IrDA, LIN, SPI, UART/USART
• Peripherals: Brown-out Detect/Reset, HLVD, POR, PWM, WDT
• Number Of I /o: 24
• Program Memory Size: 16KB (5.5K x 24)
• Program Memory Type: FLASH
• Eeprom Size: 512 x 8
• Ram Size: 2K x 8
• Voltage - Supply (vcc/vdd): 1.8 V ~ 3.6 V
• Data Converters: A/D 13x12b
• Oscillator Type: Internal
• Operating Temperature: -40°C ~ 85°C
• Package / Case: 28-SSOP (0.209", 5.30mm Width)
• Lead Free Status / Rohs Status: Lead free / RoHS Compliant

PIC24FV32KA304 FAMILY
REGISTER 7-1:
DS39995B-page 74
bit 15
bit 7
Legend:
R = Readable bit
-n = Value at POR
bit 15
bit 14
bit 13
bit 12
bit 11
bit 10
bit 9
bit 8
bit 7
bit 6
bit 5
Note 1:
R/W-0, HS
R/W-0, HS
TRAPR
EXTR
2:
3:
All of the Reset status bits may be set or cleared in software. Setting one of these bits in software does not
cause a device Reset.
If the FWDTEN Configuration bit is ‘1’ (unprogrammed), the WDT is always enabled, regardless of the
SWDTEN bit setting.
On PIC24FV32KA3xx parts only, not used on PIC24F32KA3XX.
TRAPR: Trap Reset Flag bit
1 = A Trap Conflict Reset has occurred
0 = A Trap Conflict Reset has not occurred
IOPUWR: Illegal Opcode or Uninitialized W Access Reset Flag bit
1 = An illegal opcode detection, an illegal address mode or uninitialized W register used as an Address
0 = An illegal opcode or uninitialized W Reset has not occurred
SBOREN: Software Enable/Disable of BOR bit
1 = BOR is turned on in software
0 = BOR is turned off in software
LVREN: Low-Voltage Sleep Mode
1 = Regulated voltage supply provided solely by the Low-Voltage Regulator (LVREG) during Sleep
0 = Regulated voltage supply provided by the main voltage regulator (HVREG) during Sleep
Unimplemented: Read as ‘0’
DPSLP: Deep Sleep Mode Flag bit
1 = Deep Sleep has occurred
0 = Deep Sleep has not occurred
CM: Configuration Word Mismatch Reset Flag bit
1 = A Configuration Word Mismatch Reset has occurred
0 = A Configuration Word Mismatch Reset has not occurred
PMSLP: Program Memory Power During Sleep bit
1 = Program memory bias voltage remains powered during Sleep
0 = Program memory bias voltage is powered down during Sleep and voltage regulator enters Standby mode
EXTR: External Reset (MCLR) Pin bit
1 = A Master Clear (pin) Reset has occurred
0 = A Master Clear (pin) Reset has not occurred
SWR: Software Reset (Instruction) Flag bit
1 = A RESET instruction has been executed
0 = A RESET instruction has not been executed
SWDTEN: Software Enable/Disable of WDT bit
1 = WDT is enabled
0 = WDT is disabled
R/W-0, HS
R/W-0, HS
IOPUWR
SWR
Pointer caused a Reset
RCON: RESET CONTROL REGISTER
C = Clearable bit
W = Writable bit
‘1’ = Bit is set
SWDTEN
R/W-0, HS
SBOREN
R/W-0
(2)
R/W-0, HS
LVREN
WDTO
R/W-0
(3)
(3)
HS = Hardware Settable bit
U = Unimplemented bit, read as ‘0’
‘0’ = Bit is cleared
R/W-0, HS
SLEEP
(2)
U-0
—
(1)
R/W-0, HS
R/C-0, HS
DPSLP
IDLE
 2011 Microchip Technology Inc.
x = Bit is unknown
R/W-1, HS
R/W-0
BOR
CM
R/W-1, HS
(3)
PMSLP
R/W-0
POR
bit 8
bit 0