PIC24FV16KA304T-I/MV Microchip Technology, PIC24FV16KA304T-I/MV Datasheet - Page 61

• Manufacturer Part Number: PIC24FV16KA304T-I/MV
• Description: 16KB Flash, 2KB RAM, 512B EEPROM, 16 MIPS, 12-bit ADC, CTMU, 5V 48 UQFN 6x6x0.5m
• Manufacturer: Microchip Technology
• Series: PIC® XLP™ 24Fr

Specifications of PIC24FV16KA304T-I/MV

• Processor Series: PIC24FV
• Core: PIC
• Data Bus Width: 16 bit
• Program Memory Type: Flash
• Program Memory Size: 16 KB
• Data Ram Size: 2 KB
• Maximum Operating Temperature: + 85 C
• Mounting Style: SMD/SMT
• Package / Case: UQFN-48
• Development Tools By Supplier: MPLAB IDE Software
• Minimum Operating Temperature: - 40 C
• Core Processor: PIC
• Core Size: 16-Bit
• Speed: 32MHz
• Connectivity: I²C, IrDA, LIN, SPI, UART/USART
• Peripherals: Brown-out Detect/Reset, HLVD, POR, PWM, WDT
• Number Of I /o: 38
• Eeprom Size: 512 x 8
• Ram Size: 2K x 8
• Voltage - Supply (vcc/vdd): 2 V ~ 5.5 V
• Data Converters: A/D 16x12b
• Oscillator Type: Internal
• Operating Temperature: -40°C ~ 85°C
• Lead Free Status / Rohs Status: Details

REGISTER 5-1:
 2011 Microchip Technology Inc.
bit 15
bit 7
Legend:
-n = Value at POR
‘0’ = Bit is cleared
bit 15
bit 14
bit 13
bit 12
bit 11-7
bit 6
bit 5-0
Note 1:
R/SO-0, HC
WR
U-0
—
2:
3:
4:
All other combinations of NVMOP<5:0> are no operation.
Available in ICSP™ mode only. Refer to device programming specification.
The address in the Table Pointer decides which rows will be erased.
This bit is used only while accessing data EEPROM.
WR: Write Control bit
1 = Initiates a Flash memory program or erase operation. The operation is self-timed and the bit is
0 = Program or erase operation is complete and inactive
WREN: Write Enable bit
1 = Enable Flash program/erase operations
0 = Inhibit Flash program/erase operations
WRERR: Write Sequence Error Flag bit
1 = An improper program or erase sequence attempt or termination has occurred (bit is set automatically
0 = The program or erase operation completed normally
PGMONLY: Program Only Enable bit
Unimplemented: Read as ‘0’
ERASE: Erase/Program Enable bit
1 = Perform the erase operation specified by NVMOP<5:0> on the next WR command
0 = Perform the program operation specified by NVMOP<5:0> on the next WR command
NVMOP<5:0>: Programming Operation Command Byte bits
Erase Operations (when ERASE bit is ‘1’):
1010xx = Erase entire boot block (including code-protected boot block)
1001xx = Erase entire memory (including boot block, configuration block, general block)
011010 = Erase 4 rows of Flash memory
011001 = Erase 2 rows of Flash memory
011000 = Erase 1 row of Flash memory
0101xx = Erase entire configuration block (except code protection bits)
0100xx = Erase entire data EEPROM
0011xx = Erase entire general memory block programming operations
0001xx = Write 1 row of Flash memory (when ERASE bit is ‘0’)
ERASE
WREN
R/W-0
R/W-0
cleared by hardware once the operation is complete.
on any set attempt of the WR bit)
NVMCON: FLASH MEMORY CONTROL REGISTER
x = Bit is unknown
SO = Settable Only bit
‘1’ = Bit is set
NVMOP5
WRERR
R/W-0
R/W-0
(1)
PGMONLY
NVMOP4
R/W-0
R/W-0
PIC24FV32KA304 FAMILY
(4)
(4)
(1)
(4)
(3)
(3)
(3)
HC = Hardware Clearable bit
R = Readable bit
U = Unimplemented bit, read as ‘0’
NVMOP3
R/W-0
U-0
—
(1)
NVMOP2
(1)
R/W-0
U-0
(3)
—
(1)
(2)
W = Writable bit
NVMOP1
R/W-0
U-0
—
(1)
DS39995B-page 61
(2)
NVMOP0
R/W-0
U-0
—
bit 8
bit 0
(1)