LMH6739MQ National Semiconductor, LMH6739MQ Datasheet - Page 3

• Manufacturer Part Number: LMH6739MQ
• Manufacturer: National Semiconductor

Specifications of LMH6739MQ

• Power Supply Requirement: Single
• Single Supply Voltage (typ): 9V
• Dual Supply Voltage (typ): Not RequiredV
• Single Supply Voltage (min): 8V
• Single Supply Voltage (max): 12V
• Dual Supply Voltage (min): Not RequiredV
• Dual Supply Voltage (max): Not RequiredV
• Operating Temperature Classification: Industrial
• Mounting: Surface Mount
• Pin Count: 16
• Package Type: SSOP
• Lead Free Status / RoHS Status: Not Compliant

PSRR
CMRR
I
Miscellaneous Performance
R
C
R
R
V
CMIR
I
I
I
I
V
V
CC
O
SC
IH
IL
Symbol
O
DMAX
DMIM
IN
IN
IN
O
Note 1: Absolute Maximum Ratings indicate limits beyond which damage to the device may occur. Operating Ratings indicate conditions for which the device is
intended to be functional, but specific performance is not guaranteed. For guaranteed specifications, see the Electrical Characteristics tables.
Note 2: Electrical Table values apply only for factory testing conditions at the temperature indicated. Factory testing conditions result in very limited self-heating
of the device such that T
T
Individual parameters are tested as noted.
Note 3: Human Body Model, applicable std. MIL-STD-883, Method 3015.7. Machine Model, applicable std. JESD22-A115-A (ESD MM std. of JEDEC)
Field-Induced Charge-Device Model, applicable std. JESD22-C101-C (ESD FICDM std. of JEDEC).
Note 4: The maximum output current (I
for more details.
Note 5: The maximum power dissipation is a function of T
P
Note 6: Typical values represent the most likely parametric norm as determined at the time of characterization. Actual typical values may vary over time and will
also depend on the application and configuration. The typical values are not tested and are not guaranteed on shipped production material.
Note 7: Limits are 100% production tested at 25°C. Limits over the operating temperature range are guaranteed through correlations using the Statistical Quality
Control (SQC) method.
Note 8: Parameter 100% production tested at 25° C.
Note 9: Short circuit current should be limited in duration to no more than 10 seconds. See the Power Dissipation section of the Application Information for more
details.
+
+
−
A
D
. See Applications Information for information on temperature de-rating of this device. Min/Max ratings are based on product characterization and simulation.
= (T
J(MAX)
Power Supply Rejection Ratio (Note
8)
Common Mode Rejection Ratio
(Note 8)
Supply Current (Note 8)
Supply Current Disabled V
Supply Current Disabled V
Internal Feedback & Gain Set
Resistor Value
Gain Error
Non-Inverting Input Resistance
Non-Inverting Input Capacitance
Inverting Input Impedance
Output Impedance
Output Voltage Range (Note 8)
Common Mode Input Range (Note
8)
Linear Output Current (Notes 4, 8) V
Short Circuit Current (Note 9)
Disable Pin Bias Current High
Disable Pin Bias Current Low
Voltage for Disable
Voltage for Enable
– T
A
)/ θ
JA
. All numbers apply for packages soldered directly onto a PC Board.
J
= T
Parameter
A
. No guarantee of parametric performance is indicated in the electrical tables under conditions of internal self heating where T
OUT
) is determined by device power dissipation limitations. See the Power Dissipation section of the Application Information
+
−
All three amps Enabled, No Load
R
R
R
Output impedance of input buffer.
DC
R
R
CMRR > 40 dB
V
Disable Pin = V
Disable Pin = 0V
Disable Pin
Disable Pin
J(MAX)
IN
IN
L
L
L
L
L
=
=
=
= 100Ω
=
= 0V, V
= 2V Output Shorted to Ground
, θ
∞
∞
∞
∞
JA
. The maximum allowable power dissipation at any ambient temperature is
OUT
Conditions
≤
≥
V
V
< ±30 mV
+
DMAX
DMIN
3
(Note 7)
±3.25
±3.65
±3.1
±3.5
±1.9
±1.7
48.5
Min
375
2.0
50
46
44
80
60
(Note 6)
1000
−350
±3.5
±3.8
±2.0
0.05
Typ
450
160
1.9
1.1
0.2
53
50
32
30
90
10
.8
(Note 7)
Max
±1.1
525
2.2
1.3
0.8
35
40
www.national.com
Units
mA
mA
mA
mA
mA
dB
dB
kΩ
pF
μA
μA
%
Ω
Ω
Ω
V
V
V
V
J
>