MC33882DHR2 Freescale, MC33882DHR2 Datasheet - Page 17

• Manufacturer Part Number: MC33882DHR2
• Manufacturer: Freescale

Specifications of MC33882DHR2

• Switch Type: Low Side
• Power Switch Family: MC33882
• Input Voltage: -0.3 to 7.3V
• Power Switch On Resistance: 400mOhm
• Output Current: 3A
• Number Of Outputs: 8
• Mounting: Surface Mount
• Supply Current: 7.5mA
• Package Type: HSOP
• Operating Temperature (min): -40C
• Operating Temperature Classification: Automotive
• Pin Count: 32
• Lead Free Status / RoHS Status: Compliant

both Serial Peripheral Interface (SPI) I /O as well as optional
parallel input control to each output. There are also two low-
power (30 mA) low-side switches with SPI diagnostic
feedback, but parallel-only input control. The 33882
incorporates SMARTMOS technology with CMOS logic,
VPWR Pin
is provided for overvoltage shutdown protection and for
added gate drive capabilities. A decoupling capacitor is
required from V
IN0 & IN1, IN2 & IN3, and IN4 & IN5 Pins
the
OUT1, IN2 & IN3 controls OUT2 and OUT3, while IN4 & IN5
controls OUT4 and OUT5. These pins may be connected to
PWM outputs of the control IC and pulled high or pulled low
to control output channel states while the
The states of these pins are ignored during normal operation
(
parallel) when the
active 25 μA pull-downs.
MODE Pin
IC. This pin has an internal active 25 μA pull-up. When pulled
high, the
• Disables all serial control of the outputs while still reading
• Disables parallel inputs IN0, IN1, IN2, IN3, IN4, and IN5
• Selects IN0 & IN1, IN2 & IN3, and IN4 & IN5 input pins for
• Turns off OUT6 and OUT7.
• Tri-states the SO pin.
IN0 to IN7 Pins
the control IC. Each parallel input is logic high with the
corresponding SPI control bit to control each output channel.
These pins have internal 25 μA active pull-downs.
OUT0 to OUT7 Pins
OUT5 are actively clamped to handle inductive loads.
Analog Integrated Circuit Device Data
Freescale Semiconductor
MODE
The 33882 incorporates six 1.0 A low-side switches using
The V
These input pins control two output channels each when
The
any serial input commands.
control of the outputs.
control of OUT0 and OUT1, OUT2 and OUT3, OUT4 and
OUT5, respectively.
These are parallel input pins connected to output pins of
Each pin is one channel's low-side switch output. OUT0 to
MODE
MODE
pin low) and override the normal inputs (serial or
PWR
MODE
pin is pulled high: IN0 & IN1 controls OUT0 and
pin is connected to battery voltage. This supply
pin is connected to the
PWR
pin does the following:
MODE
to ground.
pin is high. These pins have internal
MODE
MODE
FUNCTIONAL DESCRIPTION
pin of the control
FUNCTIONAL PIN DESCRIPTION
pin is high.
INTRODUCTION
bipolar / MOS analog circuitry, and DMOS power MOSFETs.
Designed to interface directly with a microcontroller, it
controls inductive or incandescent loads. Each output is
configured as an open drain transistor with dynamic
clamping.
SI Pin
Output pin of the control IC from where it receives output
command data. This input has an internal active 25 μA pull-
down and requires CMOS logic levels. The serial data
transmitted on this line is an 8- or 16-bit control command
sent MSB first, controlling the six output channels. Bits A5
through A0 control channels 5 through 0, respectively. Bits
A6 and A7 enable ON open load fault detection on channels
5 through 0. The control IC will ensure that data is available
on the rising edge of SCLK. Each channel has its serial
control bit high with its parallel input to determine its state.
SCLK Pin
SPI port. It transitions one time per bit transferred when in
operation. It is idle between command transfers. It is 50%
duty cycle and has CMOS levels. This signal is used to shift
data to and from the device. For proper fault reporting
operation, the SCLK input must be low when
from high to low.
CS Pin
control IC. The control IC controls which device is addressed
by pulling the
SPI communication with the device, while other devices on
the serial link keep their serial outputs tri-stated. This input
has an internal active 25 μA pull-up and requires CMOS logic
levels.
SO Pin
Input pin of the control IC or to the SI pin of the next device in
a daisy chain. This output will remain tri-stated unless the
device is selected by a low
The output signal generated will have CMOS logic levels and
the output data will transition on the falling edges of SCLK.
The serial output data provides fault information for each
output and is returned MSB first when the device is
addressed. Fault bit assignments for return data are as
follows: MSB-0 through MSB-7 are output fault bits for OUT7
to OUT0, respectively. In 8-bit SPI mode, under normal
The Serial Input pin is connected to the SPI Serial Data
The SCLK pin of the control IC is a bit (shift) clock for the
The
The Serial Output pin is connected to the SPI Serial Data
CS
pin is connected to a chip select output of the
CS
pin of the desired device low, enabling the
CS
pin or the
FUNCTIONAL DESCRIPTION
MODE
INTRODUCTION
CS
pin goes low.
transitions
33882
17