ADC121S021CIMF/NOPB National Semiconductor, ADC121S021CIMF/NOPB Datasheet - Page 10

• Manufacturer Part Number: ADC121S021CIMF/NOPB
• Description: ADC 12BIT 1CH 50-200KSPS SOT23-6
• Manufacturer: National Semiconductor
• Series: PowerWise®r

Specifications of ADC121S021CIMF/NOPB

• Number Of Bits: 12
• Sampling Rate (per Second): 200k
• Data Interface: DSP, MICROWIRE™, QSPI™, Serial, SPI™
• Number Of Converters: 1
• Power Dissipation (max): 7.9mW
• Voltage Supply Source: Single Supply
• Operating Temperature: -40°C ~ 85°C
• Mounting Type: Surface Mount
• Package / Case: SOT-23-6
• Lead Free Status / RoHS Status: Lead free / RoHS Compliant
• Other names: ADC121S021CIMF; ADC121S021CIMFTR

www.national.com
Applications Information
1.0 ADC121S021 OPERATION
The ADC121S021 is a successive-approximation analog-to-
digital converter designed around a charge-redistribution dig-
ital-to-analog converter core. Simplified schematics of the
ADC121S021 in both track and hold modes are shown in
Figure 3
in track mode: switch SW1 connects the sampling capacitor
to the input, and SW2 balances the comparator inputs. The
device is in this state until CS is brought low, at which point
the device moves to the hold mode.
2.0 USING THE ADC121S021
The serial interface timing diagram for the ADC is shown in
Figure
ADC and frames the serial data transfers. SCLK (serial clock)
controls both the conversion process and the timing of serial
data. SDATA is the serial data out pin, where a conversion
result is found as a serial data stream.
Basic operation of the ADC begins with CS going low, which
initiates a conversion process and data transfer. Subsequent
rising and falling edges of SCLK will be labelled with reference
to the falling edge of CS; for example, "the third falling edge
of SCLK" shall refer to the third falling edge of SCLK after
CS goes low.
At the fall of CS, the SDATA pin comes out of TRI-STATE,
and the converter moves from track mode to hold mode. The
input signal is sampled and held for conversion on the falling
edge of CS. The converter moves from hold mode to track
mode on the 13th rising edge of SCLK (see
this point that the interval for the T
the worst case, 350ns must pass between the 13th rising
2. CS is chip select, which initiates conversions on the
and
Figure
4, respectively. In
ACQ
specification begins. In
Figure
FIGURE 3. ADC121S021 in Track Mode
FIGURE 4. ADC121S021 in Hold Mode
Figure
3, the device is
2). It is at
10
Figure 4
nects the sampling capacitor to ground, maintaining the sam-
pled voltage, and switch SW2 unbalances the comparator.
The control logic then instructs the charge-redistribution DAC
to add or subtract fixed amounts of charge from the sampling
capacitor until the comparator is balanced. When the com-
parator is balanced, the digital word supplied to the DAC is
the digital representation of the analog input voltage. The de-
vice moves from hold mode to track mode on the 13th rising
edge of SCLK.
edge and the next falling edge of SCLK. The SDATA pin will
be placed back into TRI-STATE after the 16th falling edge of
SCLK, or at the rising edge of CS, whichever occurs first. After
a conversion is completed, the quiet time (t
satisfied before bringing CS low again to begin another con-
version.
Sixteen SCLK cycles are required to read a complete sample
from the ADC. The sample bits (including leading zeroes) are
clocked out on falling edges of SCLK, and are intended to be
clocked in by a receiver on subsequent rising edges of SCLK.
The ADC will produce three leading zero bits on SDATA, fol-
lowed by twelve data bits, most significant first.
If CS goes low before the rising edge of SCLK, an additional
(fourth) zero bit may be captured by the next falling edge of
SCLK.
2.1 Determining Throughput
Throughput depends on the frequency of SCLK and how
much time is allowed to elapse between the end of one con-
version and the start of another. At the maximum specified
shows the device in hold mode: switch SW1 con-
20145109
20145110
QUIET
) must be