AD5272BRMZ-20 Analog Devices Inc, AD5272BRMZ-20 Datasheet - Page 10

• Manufacturer Part Number: AD5272BRMZ-20
• Description: IC DGTL POT 20K 1024POS 10MSOP
• Manufacturer: Analog Devices Inc

Specifications of AD5272BRMZ-20

• Design Resources: Compact, Low Cost, 5 V, Variable Gain, Noninverting Amplifier Using AD5270/2 and AD8615 (CN0161) Compact, Low Cost, 5 V, Variable Gain, Inverting Amplifier Using AD5270/2 and AD8615(CN0168)
• Taps: 1024
• Resistance (ohms): 20K
• Number Of Circuits: 1
• Temperature Coefficient: 5ppm/°C
• Memory Type: Non-Volatile
• Interface: I²C, 2-Wire Serial
• Voltage - Supply: 2.7 V ~ 5.5 V, ±2.5 V ~ 2.75 V
• Operating Temperature: -40°C ~ 125°C
• Mounting Type: Surface Mount
• Package / Case: 10-MSOP, Micro10™, 10-uMAX, 10-uSOP
• Resistance In Ohms: *
• End To End Resistance: 20kohm
• Track Taper: Linear
• Resistance Tolerance: ± 1%
• No. Of Steps: 1024
• Supply Voltage Range: 2.7V To 5.5V
• Control Interface: I2C, Serial
• No. Of Pots: Single
• Lead Free Status / RoHS Status: Lead free / RoHS Compliant

AD5272/AD5274
PIN CONFIGURATION AND FUNCTION DESCRIPTIONS
Table 10. Pin Function Descriptions
Pin No.
1
2
3
4
5
6
7
8
9
10
EPAD
Mnemonic
V
A
W
V
EXT_CAP
GND
RESET
SDA
SCL
ADDR
Exposed Pad
(LFCSP Only)
DD
SS
EXT_CAP
Figure 4. MSOP Pin Configuration
V
V
DD
SS
W
A
1
2
3
4
5
(Not to Scale)
AD5272/
Description
Positive Power Supply. Decouple this pin with 0.1 μF ceramic capacitors and 10 μF capacitors.
Terminal A of RDAC. V
Wiper terminal of RDAC. V
Negative Supply. Connect to 0 V for single-supply applications. Decouple this pin with 0.1 μF ceramic capacitors
and 10 μF capacitors.
External Capacitor. Connect a 1 μF capacitor between EXT_CAP and V
rating of ≥7 V.
Ground Pin, Logic Ground Reference.
Hardware Reset Pin. Refreshes the RDAC register with the contents of the 50-TP memory register. Factory
default loads midscale until the first 50-TP wiper memory location is programmed. RESET is active low. Tie RESET
to V
Serial Data Line. This is used in conjunction with the SCL line to clock data into or out of the 16-bit input registers. It is
a bidirectional, open-drain data line that should be pulled to the supply with an external pull-up resistor.
Serial Clock Line. This is used in conjunction with the SDA line to clock data into or out of the 16-bit input registers.
Tristate Address Input. Sets the two least significant bits (Bit A1, Bit A0) of the 7-bit slave address (see Table 11).
Leave floating or tie to V
AD5274
TOP VIEW
DD
if not used.
10
9
8
7
6
RESET
ADDR
SCL
SDA
GND
SS
≤ V
SS
.
SS
A
≤ V
≤ V
W
DD
≤ V
Rev. C | Page 10 of 28
.
DD
.
EXT_CAP
NOTES
1. THE EXPOSED PAD IS LEFT FLOATING
OR IS TIED TO V
V
V
DD
SS
W
Figure 5. LFCSP Pin Configuration
A
1
2
3
4
5
SS
. This capacitor must have a voltage
AD5272/
(EXPOSED
SS
AD5274
.
PAD)
10
9
8
7
6 GND
ADDR
SCL
SDA
RESET