IC DAC 10BIT QUAD 10-MSOP

DAC104S085CIMM/NOPB

Manufacturer Part NumberDAC104S085CIMM/NOPB
DescriptionIC DAC 10BIT QUAD 10-MSOP
ManufacturerNational Semiconductor
SeriesPowerWise®
DAC104S085CIMM/NOPB datasheet
 


Specifications of DAC104S085CIMM/NOPB

Settling Time4.5µsNumber Of Bits10
Data InterfaceSerialNumber Of Converters4
Voltage Supply SourceSingle SupplyPower Dissipation (max)2.5mW
Operating Temperature-40°C ~ 105°CMounting TypeSurface Mount
Package / Case10-MSOP, Micro10™, 10-uMAX, 10-uSOPFor Use WithDAC104S085EB - BOARD EVALUATION DAC104S085
Lead Free Status / RoHS StatusLead free / RoHS CompliantOther namesDAC104S085CIMM
DAC104S085CIMMTR
1
2
3
4
5
6
7
8
9
10
11
Page 11
12
Page 12
13
Page 13
14
Page 14
15
Page 15
16
Page 16
17
Page 17
18
Page 18
19
Page 19
20
Page 20
Page 17/20

Download datasheet (433Kb)Embed
PrevNext
An input capacitance of 1.0µF without any ESR requirement
is required at the LP3985 input, while a 1.0µF ceramic ca-
pacitor with an ESR requirement of 5mΩ to 500mΩ is required
at the output. Careful interpretation and understanding of the
capacitor specification is required to ensure correct device
operation.
Like any low dropout regulator, the LP2980 requires an output
capacitor for loop stability. This output capacitor must be at
least 1.0µF over temperature, but values of 2.2µF or more will
provide even better performance. The ESR of this capacitor
should be within the range specified in the LP2980 data sheet.
Surface-mount solid tantalum capacitors offer a good combi-
nation of small size and ESR. Ceramic capacitors are attrac-
tive due to their small size but generally have ESR values that
are too low for use with the LP2980. Aluminum electrolytic
capacitors are typically not a good choice due to their large
The output voltage of this circuit for any code is found to be
V
= (V
x (D / 1024) x ((R1 + R2) / R1) - V
O
A
where D is the input code in decimal form. With V
R1 = R2,
V
= (10 x D / 1024) - 5V
O
A list of rail-to-rail amplifiers suitable for this application are
indicated in Table 2.
2.1.4 LP2980
The LP2980 is an ultra low dropout regulator with a 0.5% or
1.0% accuracy over temperature, depending upon grade. It is
available in 3.0V, 3.3V and 5V versions, among others.
FIGURE 8. Using the LP2980 regulator
size and have ESR values that may be too high at low tem-
peratures.
2.2 BIPOLAR OPERATION
The DAC104S085 is designed for single supply operation and
thus has a unipolar output. However, a bipolar output may be
obtained with the circuit in Figure 9. This circuit will provide
an output voltage range of ±5 Volts. A rail-to-rail amplifier
should be used if the amplifier supplies are limited to ±5V.
FIGURE 9. Bipolar Operation
TABLE 2. Some Rail-to-Rail Amplifiers
x R2 / R1)
AMP
A
= 5V and
A
LMC7111
LM7301
LM8261
17
20195316
20195317
 Typ V
Typ I
PKGS
OS
SUPPLY
DIP-8
0.9 mV
25 µA
SOT23-5
SO-8
0.03 mV
620 µA
SOT23-5
SOT23-5
0.7 mV
1 mA
www.national.com