IC DAC 10BIT QUAD 10-LLP

DAC104S085CISD/NOPB

Manufacturer Part NumberDAC104S085CISD/NOPB
DescriptionIC DAC 10BIT QUAD 10-LLP
ManufacturerNational Semiconductor
SeriesPowerWise®
DAC104S085CISD/NOPB datasheet
 


Specifications of DAC104S085CISD/NOPB

Settling Time4.5µsNumber Of Bits10
Data InterfaceSerialNumber Of Converters4
Voltage Supply SourceSingle SupplyPower Dissipation (max)2.5mW
Operating Temperature-40°C ~ 105°CMounting TypeSurface Mount
Package / Case10-LLPFor Use WithDAC104S085EB - BOARD EVALUATION DAC104S085
Lead Free Status / RoHS StatusLead free / RoHS CompliantOther namesDAC104S085CISDTR
1
2
3
4
5
6
7
8
9
10
11
Page 11
12
Page 12
13
Page 13
14
Page 14
15
Page 15
16
Page 16
17
Page 17
18
Page 18
19
Page 19
20
Page 20
Page 14/20

Download datasheet (433Kb)Embed
PrevNext
1.0 Functional Description
1.1 DAC SECTION
The DAC104S085 is fabricated on a CMOS process with an
architecture that consists of switches and resistor strings that
are followed by an output buffer. The reference voltage is ex-
ternally applied at V
and is shared by all four DACs.
REFIN
For simplicity, a single resistor string is shown in Figure 3.
This string consists of 1024 equal valued resistors with a
switch at each junction of two resistors, plus a switch to
ground. The code loaded into the DAC register determines
which switch is closed, connecting the proper node to the
amplifier. The input coding is straight binary with an ideal out-
put voltage of:
V
= V
x (D / 1024)
OUTA,B,C,D
REFIN
where D is the decimal equivalent of the binary code that is
loaded into the DAC register. D can take on any value be-
tween 0 and 1023. This configuration guarantees that the
DAC is monotonic.
FIGURE 3. DAC Resistor String
1.2 OUTPUT AMPLIFIERS
The output amplifiers are rail-to-rail, providing an output volt-
age range of 0V to V
when the reference is V
A
even rail-to-rail types, exhibit a loss of linearity as the output
www.national.com
approaches the supply rails (0V and V
reason, linearity is specified over less than the full output
range of the DAC. However, if the reference is less than V
there is only a loss in linearity in the lowest codes. The output
capabilities of the amplifier are described in the Electrical Ta-
bles.
The output amplifiers are capable of driving a load of 2 kΩ in
parallel with 1500 pF to ground or to V
full-scale outputs for given load currents are available in the
Electrical Characterisics Table.
1.3 RERENCE VOLTAGE
The DAC104S085 uses a single external reference that is
shared by all four channels. The reference pin, V
buffered and has an input impedance of 30 kΩ. It is recom-
mended that V
REFIN
output impedance. The reference voltage range is 1.0V to
V
, providing the widest possible output dynamic range.
A
1.4 SERIAL INTERFACE
The three-wire interface is compatible with SPI, QSPI and
MICROWIRE, as well as most DSPs and operates at clock
rates up to 40 MHz. See the Timing Diagram for information
on a write sequence.
A write sequence begins by bringing the SYNC line low. Once
SYNC is low, the data on the D
bit serial input register on the falling edges of SCLK. To avoid
misclocking data into the shift register, it is critical that
SYNC not be brought low simultaneously with a falling edge
of SCLK (see Serial Timing Diagram, Figure 2). On the 16th
falling clock edge, the last data bit is clocked in and the pro-
grammed function (a change in the DAC channel address,
mode of operation and/or register contents) is executed. At
this point the SYNC line may be kept low or brought high. Any
data and clock pusles after the 16th falling clock edge will be
ignored. In either case, SYNC must be brought high for the
minimum specified time before the next write sequence is ini-
tiated with a falling edge of SYNC.
Since the SYNC and D
are high, they should be idled low between write sequences
to minimize power consumption.
1.5 INPUT SHIFT REGISTER
The input shift register, Figure 4, has sixteen bits. The first
two bits are address bits. They determine whether the register
data is for DAC A, DAC B, DAC C, or DAC D. The address
bits are followed by two bits that determine the mode of op-
eration (writing to a DAC register without updating the outputs
of all four DACs, writing to a DAC register and updating the
outputs of all four DACs, writing to the register of all four DACs
20195307
and updating their outputs, or powering down all four outputs).
The final twelve bits of the shift register are the data bits. The
data format is straight binary (MSB first, LSB last), with all 0's
corresponding to an output of 0V and all 1's corresponding to
a full-scale output of V
input register are transferred to the DAC register on the six-
. All amplifiers,
A
teenth falling edge of SCLK. See Timing Diagram, Figure 2.
14
, in this case). For this
A
,
A
. The zero-code and
A
, is not
REFIN
be driven by a voltage source with low
line is clocked into the 16-
IN
buffers draw more current when they
IN
- 1 LSB. The contents of the serial
REFIN