IC DAC 12BIT QUAD R-R 10-MSOP

DAC124S085CIMM/NOPB

Manufacturer Part NumberDAC124S085CIMM/NOPB
DescriptionIC DAC 12BIT QUAD R-R 10-MSOP
ManufacturerNational Semiconductor
SeriesPowerWise®
DAC124S085CIMM/NOPB datasheet
 


Specifications of DAC124S085CIMM/NOPB

Settling Time6µsNumber Of Bits12
Data InterfaceDSP, MICROWIRE™, QSPI™, Serial, SPI™Number Of Converters4
Voltage Supply SourceSingle SupplyOperating Temperature-40°C ~ 105°C
Mounting TypeSurface MountPackage / Case10-MSOP, Micro10™, 10-uMAX, 10-uSOP
Number Of Channels4Resolution12b
Interface TypeSerial (3-Wire, SPI, QSPI, Microwire)Single Supply Voltage (typ)3.3/5V
Dual Supply Voltage (typ)Not RequiredVArchitectureResistor-String
Power Supply RequirementSingleOutput TypeVoltage
Integral Nonlinearity Error±8LSBSingle Supply Voltage (min)2.7V
Single Supply Voltage (max)5.5VDual Supply Voltage (min)Not RequiredV
Dual Supply Voltage (max)Not RequiredVOperating Temp Range-40C to 105C
Operating Temperature ClassificationIndustrialMountingSurface Mount
Pin Count10Package TypeMSOP
For Use WithDAC124S085EB - BOARD EVALUATION DAC124S085Lead Free Status / RoHS StatusLead free / RoHS Compliant
Power Dissipation (max)-Other namesDAC124S085CIMM
DAC124S085CIMMTR
1
2
3
4
5
6
7
8
9
10
11
Page 11
12
Page 12
13
Page 13
14
Page 14
15
Page 15
16
Page 16
17
Page 17
18
Page 18
19
Page 19
20
Page 20
Page 15/20

Download datasheet (435Kb)Embed
PrevNext
Normally, the SYNC line is kept low for at least 16 falling
edges of SCLK and the DAC is updated on the 16th SCLK
falling edge. However, if SYNC is brought high before the 16th
falling edge, the data transfer to the shift register is aborted
and the write sequence is invalid. Under this condition, the
DAC register is not updated and there is no change in the
mode of operation or in the DAC output voltages.
1.6 POWER-ON RESET
The power-on reset circuit controls the output voltages of the
four DACs during power-up. Upon application of power, the
DAC registers are filled with zeros and the output voltages are
0V. The outputs remain at 0V until a valid write sequence is
made to the DAC.
1.7 POWER-DOWN MODES
The DAC124S085 has four power-down modes, two of which
are identical. In power-down mode, the supply current drops
to 20 µA at 3V and 30 µA at 5V. The DAC124S085 is set in
power-down mode by setting OP1 and OP0 to 11. Since this
mode powers down all four DACs, the address bits, A1 and
A0, are used to select different output terminations for the
DAC outputs. Setting A1 and A0 to 00 or 11 causes the out-
puts to be tri-stated (a high impedance state). While setting
A1 and A0 to 01 or 10 causes the outputs to be terminated by
2.5 kΩ or 100 kΩ to ground respectively (see Table 1).
TABLE 1. Power-Down Modes
 Operating Mode
A1
A0
OP1
OP0
0
0
1
1
0
1
1
1
1
0
1
1
100 kΩ to GND
1
1
1
1
The bias generator, output amplifiers, resistor strings, and
other linear circuitry are all shut down in any of the power-
FIGURE 4. Input Register Contents
down modes. However, the contents of the DAC registers are
unaffected when in power-down. Each DAC register main-
tains its value prior to the ADC124S085 being powered down
unless it is changed during the write sequence which instruct-
ed it to recover from power down. Minimum power consump-
tion is achieved in the power-down mode with SYNC and
D
idled low and SCLK disabled. The time to exit power-down
IN
(Wake-Up Time) is typically t
and Timing Characteristics table.
2.0 Applications Information
2.1 USING REFERENCES AS POWER SUPPLIES
While the simplicity of the DAC124S085 implies ease of use,
it is important to recognize that the path from the reference
input (V
REFIN
Supply Rejection Ratio (PSRR). Therefore, it is necessary to
provide a noise-free supply voltage to V
lize the full dynamic range of the DAC124S085, the supply
pin (V
) and V
A
same supply voltage. Since the DAC124S085 consumes very
little power, a reference source may be used as the reference
input and/or the supply voltage. The advantages of using a
reference source over a voltage regulator are accuracy and
stability. Some low noise regulators can also be used. Listed
below are a few reference and power supply options for the
DAC124S085.
2.1.1 LM4130
The LM4130, with its 0.05% accuracy over temperature, is a
High-Z outputs
good choice as a reference source for the DAC124S085. The
2.5 kΩ to GND
4.096V version is useful if a 0 to 4.095V output range is de-
sirable or acceptable. Bypassing the LM4130 VIN pin with a
0.1µF capacitor and the VOUT pin with a 2.2µF capacitor will
High-Z outputs
improve stability and reduce output noise. The LM4130
comes in a space-saving 5-pin SOT23.
15
20173208
, which is stated in the A.C.
WU
) to the VOUTs will have essentially zero Power
. In order to uti-
REFIN
can be connected together and share the
REFIN
www.national.com