DAC124S085CISD/NOPB National Semiconductor, DAC124S085CISD/NOPB Datasheet
DAC124S085CISD/NOPB
Specifications of DAC124S085CISD/NOPB
DAC124S085CISDTR
Available stocks
Related parts for DAC124S085CISD/NOPB
DAC124S085CISD/NOPB Summary of contents
Page 1
... DAC084S085 and the 10-bit DAC104S085. The DAC124S085 operates over the extended industrial tem- perature range of −40°C to +105°C. Pin Configuration SPI ™ trademark of Motorola, Inc. © 2008 National Semiconductor Corporation Features ■ Guaranteed Monotonicity ■ Low Power Operation ■ ...
Page 2
Ordering Information Order Numbers DAC124S085CISD DAC124S085CISDX DAC124S085CIMM DAC124S085CIMMX DAC124S085EVAL Block Diagram www.national.com Temperature Range ≤ ≤ −40°C T +105°C A ≤ ≤ LLP Tape-and-Reel −40°C T +105°C A ≤ ≤ −40°C T +105°C A ≤ ≤ MSOP Tape-and-Reel −40°C T ...
Page 3
Pin Descriptions LLP MSOP Symbol Pin No OUTA V 3 OUTB V 4 OUTC 5 V OUTD 6 GND 7 V REFIN SYNC 10 SCLK PAD 11 (LLP only) Type Supply ...
Page 4
... Absolute Maximum Ratings If Military/Aerospace specified devices are required, please contact the National Semiconductor Sales Office/ Distributors for availability and specifications. Supply Voltage Voltage on any Input Pin Input Current at Any Pin (Note 3) Package Input Current (Note 3) Power Consumption 25°C A ESD Susceptibility (Note 5) ...
Page 5
Symbol Parameter I Output Short Circuit Current (sink) OS Continuous Output I O Current (Note 10) C Maximum Load Capacitance Output Impedance OUT REFERENCE INPUT CHARACTERISTICS Input Range Minimum Input Range Maximum VREFIN Input Impedance LOGIC INPUT ...
Page 6
A.C. and Timing Characteristics Values shown in this table are design targets and are subject to change before product release. The following specifications apply for 4047. Boldface limits apply for T Symbol Parameter f SCLK Frequency SCLK ...
Page 7
Note 8: To guarantee accuracy required that V Note 9: Typical figures are 25°C, and represent most likely parametric norms. Test limits are guaranteed to National's AOQL (Average Outgoing Quality J Level). Note 10: This ...
Page 8
Transfer Characteristic Timing Diagrams www.national.com FIGURE 1. Input / Output Transfer Characteristic FIGURE 2. Serial Timing Diagram 8 20173205 20173206 ...
Page 9
Typical Performance Characteristics 4047, unless otherwise stated INL 3.0V A DNL 3.0V A INL/DNL REFIN REF A SCLK 20173252 20173254 = 3.0V A 20173256 9 ...
Page 10
INL/DNL SCLK INL/DNL vs Clock Duty Cycle at V INL/DNL vs Temperature at V www.national.com = 2.7V A 20173250 = 3.0V INL/DNL vs Clock Duty Cycle 20173224 = 3.0V INL/DNL vs Temperature at ...
Page 11
Zero Code Error vs 20173230 Zero Code Error vs. f SCLK 20173234 Zero Code Error vs. Temperature 20173236 Zero Code Error vs. V Zero Code Error vs. Clock Duty Cycle Full-Scale Error vs REFIN 20173231 20173235 ...
Page 12
Full-Scale Error vs. V Full-Scale Error vs. Clock Duty Cycle Supply Current vs. V www.national.com REFIN 20173232 Full-Scale Error vs. Temperature 20173238 Supply Current vs. Temperature A 20173244 12 Full-Scale Error vs. f SCLK 20173233 20173239 20173245 ...
Page 13
Glitch Response 20173246 Power-On Reset 13 20173247 www.national.com ...
Page 14
Functional Description 1.1 DAC SECTION The DAC124S085 is fabricated on a CMOS process with an architecture that consists of switches and resistor strings that are followed by an output buffer. The reference voltage is ex- ternally applied at V ...
Page 15
Normally, the SYNC line is kept low for at least 16 falling edges of SCLK and the DAC is updated on the 16th SCLK falling edge. However, if SYNC is brought high before the 16th falling edge, the data transfer ...
Page 16
LM4050 Available with accuracy of 0.44%, the LM4050 shunt refer- ence is also a good choice as a reference for the DAC124S085 available in 4.096V and 5V versions and comes in a space-saving 3-pin SOT23. FIGURE 6. ...
Page 17
An input capacitance of 1.0µF without any ESR requirement is required at the LP3985 input, while a 1.0µF ceramic ca- pacitor with an ESR requirement of 5mΩ to 500mΩ is required at the output. Careful interpretation and understanding of the ...
Page 18
DSP/MICROPROCESSOR INTERFACING Interfacing the DAC124S085 to microprocessors and DSPs is quite simple. The following guidelines are offered to hasten the design process. 2.3.1 ADSP-2101/ADSP2103 Interfacing Figure 10 shows a serial interface between the DAC124S085 and the ADSP-2101/ADSP2103. The DSP ...
Page 19
Physical Dimensions inches (millimeters) unless otherwise noted 10-Lead MSOP Order Numbers DAC124S085CIMM NS Package Number MUB10A 10-Lead LLP Order Numbers DAC124S085CISD NS Package Number SDA10A 19 www.national.com ...
Page 20
... For more National Semiconductor product information and proven design tools, visit the following Web sites at: Products Amplifiers www.national.com/amplifiers Audio www.national.com/audio Clock and Timing www.national.com/timing Data Converters www.national.com/adc Interface www.national.com/interface LVDS www.national.com/lvds Power Management www.national.com/power Switching Regulators www.national.com/switchers LDOs www.national.com/ldo LED Lighting www ...