AD420ARZ-32 Analog Devices Inc, AD420ARZ-32 Datasheet - Page 14

• Manufacturer Part Number: AD420ARZ-32
• Description: IC DAC SRL 16BIT 24-SOIC
• Manufacturer: Analog Devices Inc

Specifications of AD420ARZ-32

• Data Interface: Serial
• Settling Time: 2.5µs
• Number Of Bits: 16
• Number Of Converters: 1
• Voltage Supply Source: Single Supply
• Power Dissipation (max): 176mW
• Operating Temperature: -40°C ~ 85°C
• Mounting Type: Surface Mount
• Package / Case: 24-SOIC (7.5mm Width)
• Resolution (bits): 16bit
• Sampling Rate: 400SPS
• Input Channel Type: Serial
• Supply Current: 4.2mA
• Digital Ic Case Style: SOIC
• No. Of Pins: 24
• Number Of Channels: 1
• Resolution: 16b
• Conversion Rate: 0.4KSPS
• Interface Type: SERIAL 3W SPI UW
• Single Supply Voltage (typ): 15/18/24V
• Dual Supply Voltage (typ): Not RequiredV
• Architecture: Delta-Sigma
• Power Supply Requirement: Single
• Output Type: Current/Voltage
• Integral Nonlinearity Error: ±0.012LSB
• Single Supply Voltage (min): 12V
• Single Supply Voltage (max): 32V
• Dual Supply Voltage (min): Not RequiredV
• Dual Supply Voltage (max): Not RequiredV
• Operating Temp Range: -40C to 85C
• Operating Temperature Classification: Industrial
• Mounting: Surface Mount
• Pin Count: 24
• Package Type: SOIC W
• Lead Free Status / RoHS Status: Lead free / RoHS Compliant
• Lead Free Status / RoHS Status: Lead free / RoHS Compliant, Lead free / RoHS Compliant

AD420
AD420 PROTECTION
TRANSIENT VOLTAGE PROTECTION
The AD420 contains ESD protection diodes, which prevent
damage from normal handling. The industrial control envir-
onment can, however, subject I/O circuits to much higher
transients. To protect the AD420 from excessively high voltage
transients, such as those specified in IEC 801, external power
diodes and a surge current limiting resistor may be required, as
shown in Figure 15. The constraint on the resistor is that during
normal operation the output voltage level at I
within its voltage compliance limit
and the two protection diodes and resistor must have
appropriate power ratings.
(I
OUT
× (Rp + R
Figure 15. Output Transient Voltage Protection
AD420
LOAD
) ≤ V
GND
V
V
CC
CC
I
OUT
CC
− 2.75 V)
R
P
R
LOAD
OUT
must remain
Rev. H | Page 14 of 16
BOARD LAYOUT AND GROUNDING
The AD420 ground pin, designated GND, is the high quality
ground reference point for the device. Any external loads on the
REF OUT and V
this reference point. Analog and digital ground currents should
not share a common path. Each signal should have an appropriate
analog or digital signal return routed close to it. Using this
approach, signal loops enclose a small area, minimizing the
inductive coupling of noise. Wide PC tracks, large gauge wire,
and ground planes are highly recommended to provide low
impedance signal paths.
POWER SUPPLIES AND DECOUPLING
The AD420 supply pins, V
decoupled to GND with 0.1 μF capacitors to eliminate high
frequency noise that may otherwise get coupled into the analog
system. High frequency ceramic capacitors are recommended.
The decoupling capacitors should be located in close proximity
to the pins and the ground line to have maximum effect. Further
reductions in noise, and improvements in performance, may be
achieved by using a larger value capacitor on the V
OUT
pins of the AD420 should be returned to
CC
(Pin 23) and V
LL
(Pin 2), should be
LL
pin.