CAT5251YI-00 ON Semiconductor, CAT5251YI-00 Datasheet

CAT5251YI-00

Manufacturer Part Number
CAT5251YI-00
Description
Manufacturer
ON Semiconductor
Datasheet

Specifications of CAT5251YI-00

Number Of Elements
4
# Of Taps
256
Resistance (max)
100KOhm
Power Supply Requirement
Single
Interface Type
Serial (SPI)
Single Supply Voltage (typ)
3.3/5V
Dual Supply Voltage (typ)
Not RequiredV
Single Supply Voltage (min)
2.5V
Single Supply Voltage (max)
6V
Dual Supply Voltage (min)
Not RequiredV
Dual Supply Voltage (max)
Not RequiredV
Operating Temp Range
-40C to 85C
Operating Temperature Classification
Industrial
Mounting
Surface Mount
Pin Count
24
Package Type
TSSOP
Lead Free Status / Rohs Status
Compliant

Available stocks

Company
Part Number
Manufacturer
Quantity
Price
Part Number:
CAT5251YI-00
Manufacturer:
CSI
Quantity:
20 000
Part Number:
CAT5251YI-00-T2
Manufacturer:
ON Semiconductor
Quantity:
1 350
Quad Digitally Programmable Potentiometer (DPP™) with
256 Taps and SPI Interface
FEATURES
PIN CONFIGURATION
© 2009 SCILLC. All rights reserved.
Characteristics subject to change without notice
For Ordering Information details, see page 14.
Four linear-taper digitally programmable
potentiometers
254 resistor taps per potentiometer
End to end resistance 50 kΩ or 100 kΩ
Potentiometer control and memory access via
SPI interface
Low wiper resistance, typically 100 Ω
Nonvolatile memory storage for up to four
wiper settings for each potentiometer
Automatic recall of saved wiper settings at
power up
2.5 to 6.0 volt operation
Standby current less than 1 µA
1,000,000 nonvolatile WRITE cycles
100 year nonvolatile memory data retention
SOIC 24-lead and TSSOP 24-lead
Industrial temperature range
R
TSSOP 24-Lead (Y)
R
R
¯¯¯ 11
¯¯¯ 12
V
WP
R
R
CS
SO
R
NC
SOIC 24-Lead (W)
A0
WO
W3
HO
CC
H3
LO
L3
10
1
2
3
4
5
6
7
8
9
5251
CAT
24 HOLD
23 SCK
22 R
21 R
20 R
19 NC
18 GND
17 R
16 R
15 R
14 A1
13 SI
¯¯¯¯¯
L2
H2
W2
W1
H1
L1
HOLD
SCK
WP
SO
CS
A0
A1
SI
1
DESCRIPTION
The
Potentiometers (DPPs™) integrated with control logic
and 16 bytes of NVRAM memory. Each DPP consists
of a series of resistive elements connected between
two externally accessible end points. The tap points
between each resistive element are connected to the
wiper outputs with CMOS switches. A separate 8-bit
control register (WCR) independently controls the
wiper tap switches for each DPP. Associated with
each wiper control register are four 8-bit non-volatile
memory data registers (DR) used for storing up to four
wiper settings. Writing to the wiper control register or
any of the non-volatile data registers is via a SPI serial
bus. On power-up, the contents of the first data
register (DR0) for each of the four potentiometers is
automatically loaded into its respective wiper control
register.
The CAT5251 can be used as a potentiometer or as a
two terminal, variable resistor. It is intended for circuit
level or system level adjustments in a wide variety of
applications. It is available in the -40°C to 85°C
industrial operating temperature range and offered in
a 24-lead SOIC and TSSOP package.
FUNCTIONAL DIAGRAM
INTERFACE
CONTROL
CAT5251
SPI BUS
LOGIC
is
NONVOLATILE
REGISTERS
REGISTERS
CONTROL
WIPER
DATA
four
Digitally
R
R
H0
L0
CAT5251
Doc. No. MD-2017 Rev. H
R
R
Programmable
H1
L1
R
R
H2
L2
R
R
H3
L3
R
R
R
R
W0
W1
W2
W3

Related parts for CAT5251YI-00

CAT5251YI-00 Summary of contents

Page 1

Quad Digitally Programmable Potentiometer (DPP™) with 256 Taps and SPI Interface FEATURES Four linear-taper digitally programmable potentiometers 254 resistor taps per potentiometer End to end resistance 50 kΩ or 100 kΩ Potentiometer control and memory access via SPI interface Low ...

Page 2

CAT5251 PIN DESCRIPTION SI: Serial Input SI is the serial data input pin. This pin is used to input all opcodes, byte addresses and data to be written to the CAT5251. Input data is latched on the rising edge of ...

Page 3

SERIAL BUS PROTOCOL The CAT5251 supports the transmission protocol. The synchronous Serial Peripheral Interface (SPI) helps the CAT5251 to interface directly with many of today's popular microcontrollers. The CAT5251 contains an 8-bit instruction register. The instruction set and the operation ...

Page 4

CAT5251 POTENTIOMETER CHARACTERISTICS Over recommended operating conditions unless otherwise stated. Symbol Parameter R Potentiometer Resistance (-00) POT R Potentiometer Resistance (-50) POT Potentiometer Resistance Tolerance R Matching POT Power Rating I Wiper Current W R Wiper Resistance W V Voltage ...

Page 5

PIN CAPACITANCE Applicable over recommended operating range from T Symbol Parameter C Output Capacitance (SO) OUT C ¯¯¯ , SCK, SI, WP Input Capacitance (CS IN A.C. CHARACTERISTICS Over recommended operating conditions unless otherwise stated. Symbol Parameter t Data ...

Page 6

CAT5251 WRITE CYCLE LIMITS Over recommended operating conditions unless otherwise stated. Symbol Parameter t Write Cycle Time WR RELIABILITY CHARACTERISTICS Over recommended operating conditions unless otherwise stated. Symbol Parameter (1) N Endurance END (1) T Data Retention DR (1) V ...

Page 7

INSTRUCTION AND REGISTER DESCRIPTION DEVICE TYPE / ADDRESS BYTE The first byte sent to the CAT5251 from the master/processor is called the Device Address Byte. The most significant four bits of the Device Type address are a device type identifier. ...

Page 8

CAT5251 WIPER CONTROL AND DATA REGISTERS Wiper Control Register (WCR) The CAT5251 contains four 8-bit Wiper Control Registers, one for each potentiometer. The Wiper Control Register output is decoded to select one of 256 switches along its resistor array. The ...

Page 9

The basic sequence of the three byte instructions is illustrated in Figure 8. These three-byte instructions exchange data between the WCR and one of the Data Registers. The WCR controls the position of the wiper. The response of the wiper ...

Page 10

CAT5251 Figure 10. Increment/Decrement INC/DEC Command Issued SCK INSTRUCTION FORMAT Read Wiper Control Register (WCR) DEVICE ADDRESSES ¯¯¯ Write Wiper Control Register (WCR) DEVICE ADDRESSES ¯¯¯ ...

Page 11

Global Transfer Data Register (DR) to Wiper Control Register (WCR) DEVICE ADDRESSES Global Transfer Wiper Control Register (WCR) to Data Register (DR) DEVICE ADDRESSES ¯¯¯ ...

Page 12

CAT5251 PACKAGING OUTLINE DRAWINGS (1)(2) SOIC 24-Lead 300 mils ( PIN#1 IDENTIFICATION TOP VIEW D A SIDE VIEW Notes: (1) All dimensions are in millimeters. Angles in degrees. (2) Complies with JEDEC standard MS-013. Doc. No. MD-2017 Rev. ...

Page 13

TSSOP 24-Lead 4.4 mm (Y) e TOP VIEW SIDE VIEW Notes: (1) All dimensions are in millimeters. Angles in degrees. (2) Complies with JEDEC standard MO-153. © 2009 SCILLC. All rights reserved. Characteristics subject to change ...

Page 14

... Y: TSSOP ORDERING INFORMATION Orderable Part Number Resistance (kΩ) CAT5251WI-50-T1 CAT5251WI-00-T1 CAT5251YI-50-T2 CAT5251YI-00-T2 CAT5251WI50 CAT5251WI00 CAT5251YI50 CAT5251YI00 Notes: (1) All packages are RoHS compliant (Lead-free, Halogen-free). (2) This device used in the above example is a CAT5251WI-50-T1 (SOIC, Industrial Temperature, 50 kΩ, Tape & Reel). ...

Page 15

... F Update Instruction Format – Read Data Register (DR) and Write Data Register (DR) 26-Nov-08 G Change logo and fine print to ON Semiconductor 31-Jul-09 H Update Ordering Information table ON Semiconductor and are registered trademarks of Semiconductor Components Industries, LLC (SCILLC). SCILLC reserves the right to make changes without further notice to any products herein ...

Related keywords