GA355QR7GB103KW01L Murata Electronics, GA355QR7GB103KW01L Datasheet - Page 223

• Manufacturer Part Number: GA355QR7GB103KW01L
• Manufacturer: Murata Electronics

!Note
No.
10
11
* "Room condition" Temperature: 15 to 35°C, Relative humidity: 45 to 75%, Atmospheric pressure: 86 to 106kPa
1
2
3
4
5
6
7
8
9
Operating
Temperature Range
Appearance
Dimensions
Dielectric Strength
Insulation Resistance
(I.R.)
Capacitance
Dissipation
Factor (D.F.)
Capacitance
Temperature
Characteristics
Strength of Metal
Terminal
Adhesive Strength
of Termination
Vibration
Resistance
• Please read rating and !CAUTION (for storage, operating, rating, soldering, mounting and handling) in this catalog to prevent smoking and/or burning, etc.
• This catalog has only typical specifi cations. Therefore, please approve our product specifi cations or transact the approval sheet for product specifi cations before ordering.
Item
Appearance No defects or abnormalities
Capacitance Within the specified tolerance
D.F.
-55 to +125°C
No defects or adnormalities
Within the specified dimensions
No defects or abnormalities
More than 10,000MΩ or 100Ω · μF (Whichever is Smaller)
Within the specified tolerance
0.01 max.
Cap. Change
Within +22/-33%
(Temp. Range: -55 to +125°C)
Termination not to be broken or loosened
No removal of the terminations or other defect should occur.
In accordance with item No.7
Specifications
KR3 Series Specifi cations and Test Methods
Reference temperature: 25°C
Visual inspection
Using calipers and micrometers
No failure should be observed when voltage in the table is
applied between the terminations for 1 to 5 sec., provided the
charge/discharge current is less than 50mA.
The inslation resisitance should be measured with
DC500V±50V (DC250V±25V in case of rated Voltage:
DC250V, DC450V) and within 60±5 sec. of charging.
The capacitance/D.F. should be measured at a frequency of
1±0.2kHz and a voltage of AC1±0.2V (r.m.s.).
The capacitance measurement should be made at each step
specified in the table.
A static load of 10N using a pressure rod should be applied to
the center in the direction of the arrow and held for 10 sec.
Solder the capacitor to the testing jig (glass epoxy board) shown
in Fig. 1.
Then apply 10N force in the direction of the arrow.
The soldering should be done using the reflow method and
should be conducted with care so that the soldering is uniform
and free defects such as heat shock.
Solder the capacitor to the test jig (glass epoxy board).
The capacitor should be subjected to a simple harmonic motion
having a total amplitude of 1.5mm, the frequency being varied
uniformly between the approximate limits of 10 and 55Hz.
The frequency range, from 10 to 55Hz and return to 10Hz,
should be traversed in approximately 1 min. This motion should
be applied for a period of 2 hrs. in each of 3 mutually
perpendicular directions (total of 6 hrs.).
Perform a heat treatment at 150+0/-10°C for 60±5 min. and
then let sit for 24±2 hrs. at room condition.*
Step
Rated Voltage
1
2
3
4
5
DC250V
DC450V
DC630V
Glass Epoxy Board
Pressure
Test Method
Max. Operating Temp. ±2
Min. Operating Temp. ±3
Glass Epoxy Board
Fig. 1
0.5L
Continued on the following page.
Temperature (°C)
10N, 10T1s
R 0.5
200% of the rated voltage
150% of the rated voltage
120% of the rated voltage
Pressure Rod
25±2
25±2
25±2
Solder
Cu
Test Voltage
205
C02E.pdf
Oct.1,2012