PVG5A201C01R00 Murata, PVG5A201C01R00 Datasheet - Page 30

• Manufacturer Part Number: PVG5A201C01R00
• Description: Trimmer Resistors - SMD 200ohms Sealed 5mm SQ 11turn
• Manufacturer: Murata

Specifications of PVG5A201C01R00

• Resistance: 200 Ohms
• Tolerance: 10 %
• Power Rating: 0.25 Watt (1/4 Watt)
• Element Type: Cermet
• Dimensions: 3.5 mm W x 4.8 mm L x 5 mm H
• Number Of Turns: 11
• Product: Multi-Turn Trimmer Potentiometers
• Temperature Coefficient: +/- 150 PPM / C
• Termination Style: SMD/SMT
• Lead Free Status / Rohs Status: Lead free / RoHS Compliant

!Note
• This PDF catalog is downloaded from the website of Murata Manufacturing co., ltd. Therefore, it’s specifications are subject to change or our products in it may be discontinued without advance notice. Please check with our
• This PDF catalog has only typical specifications because there is no space for detailed specifications. Therefore, please approve our product specifications or transact the approval sheet for product specifications before ordering.
sales representatives or product engineers before ordering.
!Note
1. Store in temperatures of -10 to +40 deg. C and
2. Do not store in or near corrosive gases.
3. Use within six months after delivery.
4. Open the package just before using.
5. Do not store under direct sunlight.
6. If you use the trimmer potentiometer in an
1. When using with partial load (rheostat), minimize
2. The maximum input voltage to a trimmer
3. The maximum input current to a trimmer
1. Soldering
2. Mounting
(1) Soldering condition
(2) Cannot be soldered using the flow soldering
(3) The soldering iron should not come in contact
(4) Apply the appropriate amount of solder paste.
(1) Use our standard land dimension. Excessive land
(2) Do not apply excessive force (preferably 4.9N
Notice (Operating and Storage Conditions)
relative humidity of 30-85%RH.
environment other than listed below, please
consult with a Murata factory representative prior
to using.
The trimmer potentiometer should not be used under
the following environmental conditions:
Notice (Rating)
the power depending on the resistance value.
potentiometer should not exceed (P
maximum operating voltage, whichever is smaller.
potentiometer should not exceed (P/R)^1/2 or the
allowable wiper current, whichever is smaller.
Notice (Soldering and Mounting)
Refer to the temperature profile.
If the soldering conditions are not
suitable, e.g., excessive time and/or excessive
temperature, the trimmer potentiometer may
deviate from the specified characteristics.
method. If you use the flow soldering method,
the trimmer potentiometer may not function.
with the case of the trimmer potentiometer. If
such contact does occur, the trimmer
potentiometer may be damaged.
If the amount of solder paste applied to the
land is insufficient, the required adhesive
strength cannot be obtained. If an excessive
amount of solder paste is applied, solder
bridging or flux overflow to the resistive
element surface can occur.
area causes displacement due to the effect of the
surface tension of the solder. Insufficient
land area leads to insufficient soldering
strength of the chip.
(Ref.; 500gf) max.), when the trimmer
potentiometer is mounted to the PCB.
• Please read rating and !CAUTION (for storage, operating, rating, soldering, mounting and handling) in this catalog to prevent smoking and/or burning, etc.
• This catalog has only typical specifications because there is no space for detailed specifications. Therefore, please approve our product specifications or transact the approval sheet for product specifications before ordering.
•
R)^1/2 or the
3. Cleaning
If the condition is not suitable, the trimmer
potentiometer may deviate from specified characteristics.
(1) Corrosive gaseous atmosphere
(2) In liquid
(3) Dusty/dirty atmosphere
(4) Direct sunlight
(5) Static voltage nor electric/magnetic fields
(6) Direct sea breeze
(7) Other variations of the above
(3) Do not warp and/or bend PC board to prevent
(4) In chip placers, the size of the cylindrical
(1) Isopropyl-alcohol and Ethyl-alcohol are
(2) Less than 3 minutes of total cleaning time by
(3) In case of ultra-sonic cleaning method, cleaning
(a) Power: 600W (67lit.) max.
(b) Frequency: 28kHz
(c) Temperature: Ambient temperature
(Ex. Chlorine gas, Hydrogen sulfide gas, Ammonia
gas, Sulfuric acid gas, Nitric oxide gas, etc.)
(Ex. Oil, Medical liquid, Organic solvent, etc.)
trimmer potentiometer from breakage.
pick-up nozzle should be outer dimension
2.5-3.0mm dia. and inner dimension
2.0-2.5mm dia.
applicable solvents for cleaning. If you use any
other types of solvents, please consult with a
Murata factory representative prior to using.
dipping, vapor and ultra-sonic method.
conditions should be as follows.
Due to ultra-sonic cleaning equipment's peculiar
self-resonance point and that cleaning
compatibility usually depends on the jig
construction and/or the cleaning condition such
as the depth of immersion, please check the
cleaning equipment to determine the suitable
conditions.
PVG3 Series Notice
R50E.pdf
29
05.9.9
4