PVG5A201C01R00 Murata, PVG5A201C01R00 Datasheet - Page 72

• Manufacturer Part Number: PVG5A201C01R00
• Description: Trimmer Resistors - SMD 200ohms Sealed 5mm SQ 11turn
• Manufacturer: Murata

Specifications of PVG5A201C01R00

• Resistance: 200 Ohms
• Tolerance: 10 %
• Power Rating: 0.25 Watt (1/4 Watt)
• Element Type: Cermet
• Dimensions: 3.5 mm W x 4.8 mm L x 5 mm H
• Number Of Turns: 11
• Product: Multi-Turn Trimmer Potentiometers
• Temperature Coefficient: +/- 150 PPM / C
• Termination Style: SMD/SMT
• Lead Free Status / Rohs Status: Lead free / RoHS Compliant

!Note
• This PDF catalog is downloaded from the website of Murata Manufacturing co., ltd. Therefore, it’s specifications are subject to change or our products in it may be discontinued without advance notice. Please check with our
• This PDF catalog has only typical specifications because there is no space for detailed specifications. Therefore, please approve our product specifications or transact the approval sheet for product specifications before ordering.
sales representatives or product engineers before ordering.
!Note
1. Store in temperatures of -10 to +40deg. C and
2. Do not store in or near corrosive gases.
3. Use within six months after delivery.
4. Open the package just before using.
5. Do not store under direct sunlight.
6. Do not use the rotary position sensor under the
1. Soldering
(1) SV01 series can be soldered by reflow soldering
(2) The dimension of land pattern used should be
(3) Soldering condition
(4) The amount of solder is critical. Insufficient
Notice (Operating and Storage Conditions)
relative humidity of 30-85%RH.
following environmental conditions. If you use
the rotary position sensor in an environment other
these listed below, please consult with Murata
factory representative prior to using.
Notice (Soldering and Mounting)
method and soldering iron. Do not use flow
soldering method (dipping).
Murata's standard land pattern at reflow
soldering. Excessive land area may cause
displacement due to the effect of the surface
tension of the solder. Insufficient land area
may cause insufficient soldering strength on PCB.
(SMD Type)
Refer to the temperature profile.
If the soldering conditions are not suitable,
e.g., excessive time and/or excessive temperature,
the rotary position sensor may deviate from the
specified characteristics.
amounts of solder can lead to insufficient
soldering strength on PCB. Excessive amounts of
solder may cause bridging between the
terminals.
• Please read rating and !CAUTION (for storage, operating, rating, soldering, mounting and handling) in this catalog to prevent smoking and/or burning, etc.
• This catalog has only typical specifications because there is no space for detailed specifications. Therefore, please approve our product specifications or transact the approval sheet for product specifications before ordering.
2. Mounting
3. Cleaning
(5) The soldering iron should not come in contact
(1) Use PCB hole to meet the pin of the rotary
(2) Do not apply excessive force (preferable 9.8N
(3) Do not warp and/or bend PCB to prevent the rotary
(1) Corrosive gasses atmosphere
(2) In liquid
(3) Dusty / dirty atmosphere
(4) Direct sunlight
(5) Static voltage nor electric/magnetic fields
(6) Direct sea breeze
(7) Other variations of the above
Cannot be cleaned because of open construction.
with the cover of the rotary position sensor. If
such contact does occur, the rotary position
sensor may be damaged.
position sensor. If the rotary position sensor
is inserted into insufficient PCB hole, the
rotary position sensor may be damaged by
mechanical stress. (Lead type)
(Ref.; 1kgf) max.), when the rotary position
sensor is mounted to the PCB.
position sensor from breakage.
(Ex. Chlorine gas, Hydrogen sulfide gas, Ammonia
gas, Sulfuric acid gas, Nitric oxide gas, etc.)
(Ex. Water, Oil, Medical liquid, Organic
solvent, etc.)
SV01 Series Notice
R50E.pdf
71
05.9.9
9