PVG5A201C01R00 Murata, PVG5A201C01R00 Datasheet - Page 76

• Manufacturer Part Number: PVG5A201C01R00
• Description: Trimmer Resistors - SMD 200ohms Sealed 5mm SQ 11turn
• Manufacturer: Murata

Specifications of PVG5A201C01R00

• Resistance: 200 Ohms
• Tolerance: 10 %
• Power Rating: 0.25 Watt (1/4 Watt)
• Element Type: Cermet
• Dimensions: 3.5 mm W x 4.8 mm L x 5 mm H
• Number Of Turns: 11
• Product: Multi-Turn Trimmer Potentiometers
• Temperature Coefficient: +/- 150 PPM / C
• Termination Style: SMD/SMT
• Lead Free Status / Rohs Status: Lead free / RoHS Compliant

!Note
• This PDF catalog is downloaded from the website of Murata Manufacturing co., ltd. Therefore, it’s specifications are subject to change or our products in it may be discontinued without advance notice. Please check with our
• This PDF catalog has only typical specifications because there is no space for detailed specifications. Therefore, please approve our product specifications or transact the approval sheet for product specifications before ordering.
sales representatives or product engineers before ordering.
!Note
1
No.
The tests and measurements should be conducted under the condition of 15 to 35°C of temperature, 25 to 75% of relative humidity and 86 to 106 kpa of
atmospheric pressure unless otherwise specified. If questionable results occur that have been measured in accordance with the above mentioned
conditions, the tests and measurements should be conducted under the condition of 25±2°C of temperature and, 45 to 55% of relative humidity and 86 to
106 kpa of atmospheric pressure.
1
2
3
4
5
6
7
8
Specifications and Test Methods
SMD Open Type (PVZ2/A2/Z3/S3/A3)/SMD Sealed Type (PVM4A_C01 Series) Specifications and Test Methods
Total Resistance
Residual Resistance
Contact Resistance
Humidity Exposure
High Temperature
Exposure
Humidity Load Life
Load Life
Temperature Cycle
• Please read rating and !CAUTION (for storage, operating, rating, soldering, mounting and handling) in this catalog to prevent smoking and/or burning, etc.
• This catalog has only typical specifications because there is no space for detailed specifications. Therefore, please approve our product specifications or transact the approval sheet for product specifications before ordering.
Item
Measure total resistance between the resistance element and terminals (terminals #1 and #3) .
Use the test voltage specified in Table-1 for total resistance measurements. This voltage should be used whenever a
subsequent total resistance measurement is made.
Position the contact arm at the extreme counterclockwise limit of mechanical travel and measure the resistance
between the contact arm and the corresponding end terminal. Then, position the contact arm at the extreme clock-
wise limit of mechanical travel and measure the resistance between the contact arm and the corresponding end ter-
minal. During this test, take suitable precautions to ensure that the rated current of the resistance element is not
exceeded.
Contact resistance variation should be measured with the measuring circuit shown below, or its equivalent. The
operating wiper should be rotated in both directions through 90% of the actual effective-electrical travel for a total of
6 cycles.
The rate of rotation of the operating wiper should be such that the wiper completes 1 count in determining whether or
not a contact resistance variation is observed at least twice in the same location. The test current should follow the
value given in Table-2 unless otherwise limited by the power rating.
The wiper contact point should be preset at about 50% position of effective rotational angle. After that, the poten-
tiometer should be placed in a chamber at 40±2°C and 90 - 95% without loading for 500±12 hours.
The resistance value should be measured after keeping the potentiometer in a room for 5±1/6 hours.
The wiper contact point should be preset at about 50% position of effective rotational angle. After that, the poten-
tiometer should be placed in a chamber at 70±2°C without loading for 500±12 hours. The resistance value should be
measured after keeping the potentiometer in a room for 1.5±1/6 hours.
The wiper contact point should be preset at about 50% position of effective rotational angle. After that, the poten-
tiometer should be placed in a chamber at 40±2°C and 90 - 95% with loading the 1/2 rated voltage between #1 and
#2 terminals, intermittently 1.5 hours ON and 0.5 hours OFF for 1000±12 hours.
The resistance value should be measured after keeping the potentiometer in a room for 5±1/6 hours.
The wiper contact point should be preset at about 50% position of effective rotational angle. After that, the poten-
tiometer should be placed in a chamber at 70±2°C (50±2°C for PVZ) with loading the 1/2 rated voltage between #1
and #2 terminals, intermittently 1.5 hours ON and 0.5 hours OFF for 1000±12 hours. The resistance value should be
measured after keeping the potentiometer in a room for 1.5±1/6 hours.
The wiper contact point should be preset at about 50% position of effective rotational angle. After that, the poten-
tiometer should be subjected to Table 3,Table 4 temperature for 5 cycles. The resistance value should be measured
after keeping the potentiometer in a room for 1.5±10 minutes.
Resistance R (ohm)
Temp. (°C)
Time (min.)
Sequence
Total Resistance,
100kFR
Standard Total
100kVR
Nominal (ohm)
Table 1: Total resistance test voltage
100FRV1k
100VRF10k
10kFRV100k
10kVRF100k
10VRV100
1kFRV10k
Table 2: Test current for CRV
-25±3
30±3
1
Table 3: PVZ
10 max.
+25±2
Maximum Test
2
Test Current
100µA max.
Voltage (V)
10mA max.
1mA max.
100.0
10.0
30.0
1.0
3.0
+85±3
30±3 10 max.
3
+25±2
4
Test Methods
Constant Current
Source
(Test current
shown in Table 2)
Time (min.)
Temp. (°C)
Sequence
Table 4: PVA2/PVA3/PVS3/PVM4A---C01
Rx : Trimmer Potentiometer
Oscilloscope bandwidth: 100Hz to 50kHz
Figure 1: CRV measuring circuit
#1
-55±3
Proofread
Resistence
30±3
1
#2
Rx
#3
10 max.
+25±2
Continued on the following page.
2
+125±3 +25±2
30±3 10 max.
3
AC
Amplifier
4
Oscilloscope
R50E.pdf
75
05.9.9
9