ADSP-2186BST-133R Analog Devices Inc, ADSP-2186BST-133R Datasheet - Page 15

• Manufacturer Part Number: ADSP-2186BST-133R
• Description: IC DSP CONTROLLER 16BIT 100LQFP
• Manufacturer: Analog Devices Inc
• Series: ADSP-21xxr
• Type: Fixed Pointr

Specifications of ADSP-2186BST-133R

• Rohs Status: RoHS non-compliant
• Interface: Host Interface, Serial Port
• Clock Rate: 33.3MHz
• Non-volatile Memory: External
• On-chip Ram: 40kB
• Voltage - I/o: 5.00V
• Voltage - Core: 5.00V
• Operating Temperature: -40°C ~ 85°C
• Mounting Type: Surface Mount
• Package / Case: 100-LQFP
• Device Core Size: 16b
• Format: Fixed Point
• Clock Freq (max): 33.3MHz
• Mips: 33.3
• Device Input Clock Speed: 33.3MHz
• Ram Size: 40KB
• Operating Supply Voltage (typ): 5V
• Operating Supply Voltage (min): 4.5V
• Operating Supply Voltage (max): 5.5V
• Operating Temp Range: -40C to 85C
• Operating Temperature Classification: Industrial
• Mounting: Surface Mount
• Pin Count: 100
• Package Type: LQFP
• Lead Free Status / Rohs Status: Not Compliant

ESD SENSITIVITY
ESD (electrostatic discharge) sensitive device. Electrostatic charges as high as 4000 V readily
accumulate on the human body and test equipment and can discharge without detection. Although
the ADSP-2186 features proprietary ESD protection circuitry, permanent damage may occur on
devices subjected to high-energy electrostatic discharges. Therefore, proper ESD precautions are
recommended to avoid performance degradation or loss of functionality.
TIMING PARAMETERS
GENERAL NOTES
Use the exact timing information given. Do not attempt to
derive parameters from the addition or subtraction of others.
While addition or subtraction would yield meaningful results for
an individual device, the values given in this data sheet reflect
statistical variations and worst cases. Consequently, you cannot
meaningfully add up parameters to derive longer times.
TIMING NOTES
Switching characteristics specify how the processor changes its
signals. You have no control over this timing—circuitry external
to the processor must be designed for compatibility with these
signal characteristics. Switching characteristics tell you what the
processor will do in a given circumstance. You can also use
switching characteristics to ensure that any timing requirement
of a device connected to the processor (such as memory) is
satisfied.
Timing requirements apply to signals that are controlled by
circuitry external to the processor, such as the data input for a
read operation. Timing requirements guarantee that the proces-
sor operates correctly with other devices.
ABSOLUTE MAXIMUM RATINGS
Supply Voltage . . . . . . . . . . . . . . . . . . . . . . . . . –0.3 V to +7 V
Input Voltage . . . . . . . . . . . . . . . . . . . . –0.3 V to V
Output Voltage Swing . . . . . . . . . . . . . –0.3 V to V
Operating Temperature Range (Ambient) . . –40°C to +85°C
Storage Temperature Range . . . . . . . . . . . . –65°C to +150°C
Lead Temperature (5 sec) LQFP . . . . . . . . . . . . . . . . . 280°C
Stresses above those listed under Absolute Maximum Ratings may cause perma-
nent damage to the device. These are stress ratings only; functional operation of
the device at these or any other conditions above those indicated in the operational
sections of this specification is not implied. Exposure to absolute maximum rating
conditions for extended periods may affect device reliability.
DD
DD
+ 0.3 V
+ 0.3 V
MEMORY TIMING SPECIFICATIONS
The table below shows common memory device specifications
and the corresponding ADSP-2186 timing parameters, for your
convenience.
Memory
Device
Specification
Address Setup to
Address Setup to
Address Hold Time
Data Setup Time
Data Hold Time
OE to Data Valid
Address Access Time t
xMS = PMS, DMS, BMS, CMS, IOMS.
FREQUENCY DEPENDENCY FOR TIMING
SPECIFICATIONS
t
with a frequency equal to half the instruction rate; for example,
a 20 MHz input clock (which is equivalent to 50 ns) yields a
25 ns processor cycle (equivalent to 40 MHz). t
the range of 0.5 t
timing parameters to obtain the specification value.
Example: t
CK
Write Start
Write End
is defined as 0.5 t
CKH
= 0.5 t
CKI
period should be substituted for all relevant
CKI
CK
ADSP-2186 Timing
Timing
Parameter
t
t
t
t
t
t
ASW
AW
WRA
DW
DH
RDD
AA
. The ADSP-2186 uses an input clock
– 7 ns = 0.5 (25 ns) – 7 ns = 5.5 ns
WARNING!
Parameter
Definition
A0–A13, xMS Setup
before WR Low
A0–A13, xMS Setup
before WR Deasserted
A0–A13, xMS Hold before
WR Low
Data Setup before WR
High
Data Hold after WR High
RD Low to Data Valid
A0–A13, xMS to Data
Valid
ADSP-2186
ESD SENSITIVE DEVICE
CK
values within