AD9951YSVZ Analog Devices Inc, AD9951YSVZ Datasheet - Page 8

• Manufacturer Part Number: AD9951YSVZ
• Description: IC DDS DAC 14BIT 1.8V 48-TQFP
• Manufacturer: Analog Devices Inc

Specifications of AD9951YSVZ

• Resolution (bits): 14 b
• Master Fclk: 400MHz
• Tuning Word Width (bits): 32 b
• Voltage - Supply: 1.71 V ~ 1.96 V
• Operating Temperature: -40°C ~ 105°C
• Mounting Type: Surface Mount
• Package / Case: 48-TQFP Exposed Pad, 48-eTQFP, 48-HTQFP, 48-VQFP
• Data Rate: 25Mbps
• Rf Ic Case Style: TQFP
• No. Of Pins: 48
• Supply Voltage Range: 1.8V To 3.3V
• Operating Temperature Range: -40°C To +105°C
• Msl: MSL 3 - 168 Hours
• Ic Function: Direct Digital Synthesizer
• Digital Ic Case Style: TQFP
• Svhc: No SVHC (15-Dec-2010)
• Rohs Compliant: Yes
• Termination Type: SMD
• Ic Generic Number: 9951
• Base Number: 9951
• Filter Terminals: SMD
• Lead Free Status / RoHS Status: Lead free / RoHS Compliant
• For Use With: AD9951/PCB - BOARD EVAL FOR AD9951
• Lead Free Status / Rohs Status: Compliant

AD9951
PIN FUNCTION DESCRIPTIONS
Table 3. Pin Function Descriptions—48-Lead TQFP/EP
Pin No.
1
2, 34
3, 33, 42, 47,
48
4, 6, 13, 16,
18, 19, 25,
27, 29
5, 7, 14, 15,
17, 22, 26,
28, 30, 31,
32
8
9
10
11
12
20
21
23
24
35
36
37
38
39
40
41
43
44
45
46
<49>
Mnemonic
I/O UPDATE
DVDD
DGND
AVDD
AGND
OSC/REFCLK
OSC/REFCLK
CRYSTAL OUT
CLKMODESELECT
LOOP_FILTER
IOUT
IOUT
DACBP
DAC_R
PWRDWNCTL
RESET
IOSYNC
SDO
CS
SCLK
SDIO
DVDD_I/O
SYNC_IN
SYNC_CLK
OSK
AGND
SET
I/O
I
I
I
I
I
I
I
O
I
I
O
O
I
I
I
I
I
O
I
I
I/O
I
I
O
I
I
Description
The rising edge transfers the contents of the internal buffer memory to the I/O registers. This pin
must be set up and held around the SYNC_CLK output signal.
Digital Power Supply Pins (1.8 V).
Digital Power Ground Pins.
Analog Power Supply Pins (1.8 V).
Analog Power Ground Pins.
Complementary Reference Clock/Oscillator Input. When the REFCLK port is operated in single-
ended mode, REFCLKB should be decoupled to AVDD with a 0.1 µF capacitor.
Reference Clock/Oscillator Input. See Clock Input section for details on the OSCILLATOR/REFCLK
operation.
Output of the Oscillator Section.
Control Pin for the Oscillator Section. When high, the oscillator section is enabled. When low, the
oscillator section is bypassed.
This pin provides the connection for the external zero compensation network of the REFCLK
multiplier’s PLL loop filter. The network consists of a 1 kΩ resistor in series with a 0.1 µF capacitor
tied to AVDD.
Complementary DAC Output. Should be biased through a resistor to AVDD, not AGND.
DAC Output. Should be biased through a resistor to AVDD, not AGND.
DAC Biasline Decoupling Pin.
A resistor (3.92 kΩ nominal) connected from AGND to DAC_R
for the DAC.
Input Pin Used as an External Power-Down Control (see Table 8 for details).
Active High Hardware Reset Pin. Assertion of the RESET pin forces the AD9951 to the initial state,
as described in the I/O port register map.
Asynchronous Active High Reset of the Serial Port Controller. When high, the current I/O
operation is immediately terminated, enabling a new I/O operation to commence once IOSYNC is
returned low. If unused, ground this pin; do not allow this pin to float.
When operating the I/O port as a 3-wire serial port, this pin serves as the serial data output. When
operated as a 2-wire serial port, this pin is unused and can be left unconnected.
This pin functions as an active low chip select that allows multiple devices to share the I/O bus.
This pin functions as the serial data clock for I/O operations.
When operating the I/O port as a 3-wire serial port, this pin serves as the serial data input, only.
When operated as a 2-wire serial port, this pin is the bidirectional serial data pin.
Digital Power Supply (for I/O Cells Only, 3.3 V).
Input Signal Used to Synchronize Multiple AD9951s. This input is connected to the SYNC_CLK
output of a master AD9951.
Clock Output Pin that Serves as a Synchronizer for External Hardware.
Input Pin Used to Control the Direction of the Shaped On-Off Keying Function when
Programmed for Operation. OSK is synchronous to the SYNC_CLK pin. When OSK is not
programmed, this pin should be tied to DGND.
The exposed paddle on the bottom of the package is a ground connection for the DAC and must
be attached to AGND in any board layout.
Rev. 0 | Page 8 of 28
SET
establishes the reference current