RTE-P2D12 IDEC Corporation, RTE-P2D12 Datasheet - Page 5

• Manufacturer Part Number: RTE-P2D12
• Description: Relay; SSR; Timing; Multi-Function; DPDT; Cur-Rtg 10A; Ctrl-V 12DC; Vol-Rtg 240/30AC/DC
• Manufacturer: IDEC Corporation

Specifications of RTE-P2D12

• Brand/series: RTE Series
• Contact Form: DPDT
• Current, Rating: 10 A
• Function: Timing
• Mounting Type: PCB
• Number Of Pins: 11
• Relay Type: Solid State
• Standards: cULus, CE, TUV
• Temperature, Operating, Maximum: 65 °C
• Temperature, Operating, Minimum: -20 °C
• Termination: Solder
• Timer Type: Multi-Function
• Timing Range: 0.1 sec. to 600 hrs.
• Voltage, Control: 12 VDC
• Voltage, Rating: 240⁄30 VAC⁄VDC
• Multifunction Operation: On-Delay/Interval or Off-Delay/Single-Shot
• Lead Free Status / Rohs Status: RoHS Compliant part

802
Special expertise is required to use Electronic Timers.
•
•
•
•
Warnings
Warning notices are used to emphasize that improper operation may cause
severe personal injury or death.
•
•
Installation of Hold-Down Springs
DIN Rail Mount Socket
Socket SR2P-06
All Electronic Timers are manufactured under IDEC’s rigorous quality control
system, but users must add a backup or fail safe provision to the control
system when using the Electronic Timer in applications where heavy damage
or personal injury may occur should the Electronic Timer fail.
Install the Electronic Timer according to instructions described in this catalog.
Make sure that the operating conditions are as described in the specifi ca-
tions. If you are uncertain about the specifi cations, contact IDEC in advance.
In these directions, safety precautions are categorized in order of importance
under Warning and Caution.
Turn power off to the Electronic timer before starting installation, removal,
wiring, maintenance, and inspection on the Electronic Timer.
Failure to turn power off may cause electrical shocks or fi re hazard.
Insert the springs into the outer
slots with the projections
facing inside.
Hold-down Spring (sold separately)
SFA-202 (use two springs)
RTE Series
Mounting A
10A
7A
Socket SR2P-05
Ambient Temperature
Mounting A
Derating Curve
Temperature Derating Curves
50
Safety Precautions
º
C 65
Insert the springs
into the slots.
Hold-down Spring (sold separately)
SFA-203 (use two springs)
Instructions
www.idec.com
º
C
•
Caution
Caution notices are used where inattention might cause personal injury or dam-
age to equipment.
•
•
•
•
•
Do not use the Electronic Timer for an emergency stop circuit or inter-
locking circuit. If the Electronic Timer should fail, a machine malfunction,
breakdown, or accident may occur.
The Electronic Timer is designed for installation in equipment. Do not install
the Electronic Timer outside equipment.
Install the Electronic Timer in environments described in the specifi cations. If
the Electronic Timer is used in places where it will be subjected to high-tem-
perature, high-humidity, condensation, corrosive gases, excessive vibrations,
or excessive shocks, then electrical shocks, fi re hazard, or malfunction could
result.
Use an IEC60127-approved fuse and circuit breaker on the power and output
line outside the Electronic Timer.
Do not disassemble, repair, or modify the Electronic Timer.
When disposing of the Electronic Timer, do so as industrial waste.
Mounting B
Switch Settings
1. Turn the selectors securely using a fl at screw-
2. Since changing the setting during timer operation
driver 4mm wide (maximum).
Note that incorrect setting may cause malfunc-
tion. Do not turn the selectors beyond their limits.
may cause malfunction, turn power off before
changing.
Operator Mode Selector
Scale Selector
Time Range Selector
7A
5A
Ambient Temperature
Mounting B
Derating Curve
50
º
C 65
º
C
Timers