PIC17C756A-33/L Microchip Technology Inc., PIC17C756A-33/L Datasheet - Page 179

• Manufacturer Part Number: PIC17C756A-33/L
• Description: 68 PIN, 32 KB OTP, 902 RAM, 50 I/O
• Manufacturer: Microchip Technology Inc.

Specifications of PIC17C756A-33/L

• A/d Inputs: 12-Channel, 10-Bit
• Cpu Speed: 8.25 MIPS
• Eeprom Memory: 0 Bytes
• Input Output: 52
• Interface: I2C/SPI/USART
• Memory Type: OTP
• Number Of Bits: 8
• Package Type: 68-pin PLCC
• Programmable Memory: 32K Bytes
• Ram Size: 902 Bytes
• Speed: 16 MHz
• Timers: 2-8-bit, 2-16-bit
• Voltage, Range: 3-5.5 V
• Lead Free Status / Rohs Status: RoHS Compliant part

16.0
The analog-to-digital (A/D) converter module has
twelve analog inputs for the PIC17C75X devices and
sixteen for the PIC17C76X devices.
The analog input charges a sample and hold capacitor.
The output of the sample and hold capacitor is the input
into the converter. The converter then generates a dig-
ital result of this analog level via successive approxima-
tion. This A/D conversion of the analog input signal,
results in a corresponding 10-bit digital number.
The analog reference voltages (positive and negative
supply) are software selectable to either the device’s
supply voltages (AV
the RG3/AN0/V
REGISTER 16-1: ADCON0 REGISTER (ADDRESS: 14h, BANK 5)
2000 Microchip Technology Inc.
bit 7-4
bit 3
bit 2
bit 1
bit 0
ANALOG-TO-DIGITAL
CONVERTER (A/D) MODULE
REF
+ and RG2/AN1/V
DD
bit 7
CHS3:CHS0: Analog Channel Select bits
0000 = channel 0, (AN0)
0001 = channel 1, (AN1)
0010 = channel 2, (AN2)
0011 = channel 3, (AN3)
0100 = channel 4, (AN4)
0101 = channel 5, (AN5)
0110 = channel 6, (AN6)
0111 = channel 7, (AN7)
1000 = channel 8, (AN8)
1001 = channel 9, (AN9)
1010 = channel 10, (AN10)
1011 = channel 11, (AN11)
1100 = channel 12, (AN12) (PIC17C76X only)
1101 = channel 13, (AN13) (PIC17C76X only)
1110 = channel 14, (AN14) (PIC17C76X only)
1111 = channel 15, (AN15) (PIC17C76X only)
11xx = RESERVED, do not select (PIC17C75X only)
Unimplemented: Read as ’0’
GO/DONE: A/D Conversion Status bit
If ADON = 1:
1 = A/D conversion in progress (setting this bit starts the A/D conversion, which is automatically
0 = A/D conversion not in progress
Unimplemented: Read as ’0’
ADON: A/D On bit
1 = A/D converter module is operating
0 = A/D converter module is shut-off and consumes no operating current
Legend:
R = Readable bit
- n = Value at POR Reset
, AVss), or the voltage level on
R/W-0
CHS3
cleared by hardware when the A/D conversion is complete)
R/W-0
CHS2
REF
- pins.
R/W-0
CHS1
W = Writable bit
’1’ = Bit is set
R/W-0
CHS0
The A/D converter has a unique feature of being able
to operate while the device is in SLEEP mode. To oper-
ate in SLEEP, the A/D clock must be derived from the
A/D’s internal RC oscillator.
The A/D module has four registers. These registers
are:
• A/D Result High Register (ADRESH)
• A/D Result Low Register (ADRESL)
• A/D Control Register0 (ADCON0)
• A/D Control Register1 (ADCON1)
The ADCON0 register, shown in Register 16-1, con-
trols the operation of the A/D module. The ADCON1
register, shown in Register 16-2, configures the func-
tions of the port pins. The port pins can be configured
as analog inputs (RG3 and RG2 can also be the volt-
age references), or as digital I/O.
U = Unimplemented bit, read as ‘0’
’0’ = Bit is cleared
U-0
—
GO/DONE
R/W-0
PIC17C7XX
x = Bit is unknown
DS30289B-page 179
U-0
—
R/W-0
ADON
bit 0