MAX3430CPA+ Maxim Integrated Products, MAX3430CPA+ Datasheet
MAX3430CPA+
Specifications of MAX3430CPA+
Related parts for MAX3430CPA+
MAX3430CPA+ Summary of contents
Page 1
... DIP/SO ________________________________________________________________ Maxim Integrated Products For pricing, delivery, and ordering information, please contact Maxim/Dallas Direct! at 1-888-629-4642, or visit Maxim’s website at www.maxim-ic.com. ±80V Fault-Protected, Fail-Safe, o ±80V Fault Protection o ±12kV ESD Protection o +3.3V Operation o Internal Slew-Rate Limiting o 250kbps Data Rate o Allows Up to 128 Transceivers on the Bus ...
Page 2
Fault-Protected, Fail-Safe, 1/4-Unit Load, +3.3V RS-485 Transceiver ABSOLUTE MAXIMUM RATINGS (All voltages are referenced to GND.) V ........................................................................................+5V CC RE, DE, DI...................................................-0. Driver Output Voltage (A, B) (Note 1) ..................................±80V Receiver Input Voltage (A, B) (Note 1) ...
Page 3
Load, +3.3V RS-485 Transceiver DC ELECTRICAL CHARACTERISTICS (continued +3.3V ±10 MIN MAX PARAMETER SYMBOL RECEIVER LOGIC RO Output High Voltage RO Output Low Voltage Three-State Output Current at Receiver Receiver ...
Page 4
Fault-Protected, Fail-Safe, 1/4-Unit Load, +3.3V RS-485 Transceiver DRIVER SWITCHING CHARACTERISTICS = +3.3V ±10 unless otherwise noted. Typical values are MIN MAX PARAMETER SYMBOL t DPLH Driver Propagation Delay ...
Page 5
Load, +3.3V RS-485 Transceiver (V = +3.3V +25°C, unless otherwise noted SUPPLY CURRENT vs. TEMPERATURE -40 - ...
Page 6
Fault-Protected, Fail-Safe, 1/4-Unit Load, +3.3V RS-485 Transceiver Figure 1. Driver DC Test Load DPHL DPLH 1/2 ...
Page 7
Load, +3.3V RS-485 Transceiver Figure 6. Receiver Propagation Delays S3 +1.5V -1.5V GENERATOR RE t RZH RO RE 1.5V t RHZ RO 0.25V Figure 7. Receiver Enable and Disable Times _______________________________________________________________________________________ ±80V Fault-Protected, Fail-Safe, Test ...
Page 8
Fault-Protected, Fail-Safe, 1/4-Unit Load, +3.3V RS-485 Transceiver PIN NAME 1 RO Receiver Output Receiver Output Enable enabled when RE is low high impedance when RE is high. The RE 2 device enters a low-power shutdown ...
Page 9
Load, +3.3V RS-485 Transceiver Detailed Description The driver accepts a single-ended, logic-level input (DI) and transfers differential, RS-485 level output (A and B). Driving DE high enables the driver, while pulling DE low places the driver ...
Page 10
Fault-Protected, Fail-Safe, 1/4-Unit Load, +3.3V RS-485 Transceiver stage, provides immediate protection against short cir- cuits over the whole common-mode voltage range. The second, a thermal shutdown circuit, forces the driver outputs into a high-impedance state if the die tempera- ...
Page 11
Load, +3.3V RS-485 Transceiver Applications Information 128 Transceivers on the Bus The standard RS-485 receiver input impedance is 12kΩ (one-unit load), and a standard driver can drive up to 32-unit loads. The MAX3430 transceiver 1/4-unit-load receiver input impedance (48kΩ) ...
Page 12
Fault-Protected, Fail-Safe, 1/4-Unit Load, +3.3V RS-485 Transceiver (The package drawing(s) in this data sheet may not reflect the most current specifications. For the latest package outline information www.maxim-ic.com/packages TOP VIEW ...
Page 13
... Maxim cannot assume responsibility for use of any circuitry other than circuitry entirely embodied in a Maxim product. No circuit patent licenses are implied. Maxim reserves the right to change the circuitry and specifications without notice at any time. Maxim Integrated Products, 120 San Gabriel Drive, Sunnyvale, CA 94086 408-737-7600 ____________________ 13 © 2003 Maxim Integrated Products ± ...