ATTINY12-8SU Atmel, ATTINY12-8SU Datasheet - Page 48

• Manufacturer Part Number: ATTINY12-8SU
• Description: Microcontrollers (MCU) AVR 1K FLASH 64B EE 5V 8MHZ
• Manufacturer: Atmel

Specifications of ATTINY12-8SU

• Processor Series: ATTINY1x
• Core: AVR8
• Data Bus Width: 8 bit
• Program Memory Type: Flash
• Program Memory Size: 1 KB
• Maximum Clock Frequency: 8 MHz
• Number Of Programmable I/os: 6
• Number Of Timers: 1
• Maximum Operating Temperature: + 85 C
• Mounting Style: SMD/SMT
• Package / Case: SOIC
• 3rd Party Development Tools: EWAVR, EWAVR-BL
• Development Tools By Supplier: ATAVRDRAGON, ATSTK500
• Minimum Operating Temperature: - 40 C
• Cpu Family: ATtiny
• Device Core: AVR
• Device Core Size: 8b
• Frequency (max): 8MHz
• Interface Type: SPI
• # I/os (max): 6
• Number Of Timers - General Purpose: 1
• Operating Supply Voltage (typ): 5V
• Operating Supply Voltage (max): 5.5V
• Operating Supply Voltage (min): 4V
• Instruction Set Architecture: RISC
• Operating Temp Range: -40C to 85C
• Operating Temperature Classification: Industrial
• Mounting: Surface Mount
• Pin Count: 8
• Package Type: SOIC EIAJ
• Lead Free Status / Rohs Status: Details

Memory
Programming
Program (and Data)
Memory Lock Bits
Fuse Bits in ATtiny11
Fuse Bits in ATtiny12
48
ATtiny11/12
The ATtiny11/12 MCU provides two lock bits which can be left unprogrammed (“1”) or
can be programmed (“0”) to obtain the additional features listed in Table 21. The lock
bits can only be erased with the Chip Erase command
Table 21. Lock Bit Protection Modes
Note:
The ATtiny11 has five fuse bits, FSTRT, RSTDISBL and CKSEL2..0.
•
•
•
The status of the fuse bits is not affected by Chip Erase.
Note:
The ATtiny12 has eight fuse bits, BODLEVEL, BODEN, SPIEN, RSTDISBL and
CKSEL3..0. All the fuse bits are programmable in both High-voltage and Low-voltage
Serial programming modes. Changing the fuses does not have any effect while in pro-
gramming mode.
•
•
•
•
Mode
Memory Lock Bits
1
2
3
FSTRT: See Table 8, “Start-up Times for the ATtiny11 (V
which value to use. Default value is unprogrammed (“1”).
When RSTDISBL is programmed (“0”), the external reset function of pin PB5 is
disabled.
CKSEL2..0: See Table 3, “Device Clocking Options Select,” on page 10, for which
combination of CKSEL2..0 to use. Default value is “100”, internal RC oscillator.
The BODLEVEL Fuse selects the Brown-out Detection level and changes the start-
up times. See “Brown-out Detection (ATtiny12)” on page 27. See Table 10,
“ATtiny12 Clock Options and Start-up Times,” on page 25. Default value is
programmed (“0”).
When the BODEN Fuse is programmed (“0”), the Brown-out Detector is enabled.
See “Brown-out Detection (ATtiny12)” on page 27. Default value is unprogrammed
(“1”).
When the SPIEN Fuse bit is programmed (“0”), Low-Voltage Serial Program and
Data Downloading is enabled. Default value is programmed (“0”). Unprogramming
this fuse while in the Low-Voltage Serial Programming mode will disable future in-
system downloading attempts.
When the RSTDISBL Fuse is programmed (“0”), the external reset function of pin
PB5 is disabled.
while in the Low-Voltage Serial Programming mode will disable future in-system
downloading attempts.
1. In the High-voltage Serial Programming mode, further programming of the fuse bits
1. If the RSTDISBL Fuse is programmed, then the programming hardware should apply
LB1
1
0
0
are also disabled. Program the fuse bits before programming the lock bits.
+12V to PB5 while the ATtiny11 is in Power-on Reset. If not, the part can fail to enter
programming mode caused by drive contention on PB0.
(1)
Default value is unprogrammed (“1”).
LB2
1
1
0
(1)
Protection Type
No memory lock features enabled.
Further programming of the Flash (and EEPROM for ATtiny12) is
disabled.
Same as mode 2, and verify is also disabled.
Default value is unprogrammed (“1”). Programming this fuse
(1)
.
CC
= 2.7V),” on page 23 for
1006F–AVR–06/07