SI3015-BS Silicon Laboratories Inc, SI3015-BS Datasheet - Page 54

• Manufacturer Part Number: SI3015-BS
• Description: IC ISOMODEM LINE-SIDE 16SOIC
• Manufacturer: Silicon Laboratories Inc
• Type: Enhanced Global Direct Access Arrangementr

Specifications of SI3015-BS

• Package / Case: 16-SOIC (3.9mm Width)
• Data Format: V.90
• Interface: Serial
• Voltage - Supply: 3.3 V ~ 5 V
• Mounting Type: Surface Mount
• Product: Modem Module
• Supply Current: 0.3 mA
• Maximum Operating Temperature: + 85 C
• Minimum Operating Temperature: - 40 C
• Mounting Style: SMD/SMT
• Lead Free Status / RoHS Status: Contains lead / RoHS non-compliant
• Baud Rates: -
• Lead Free Status / RoHS Status: Lead free / RoHS Compliant, Contains lead / RoHS non-compliant

Si3038
A
Various countries are expected to adopt the IEC
CISPR22 standard over the next few years. For
example, the European Union (EU) has adopted a
standard entitled EN55022, which is based on the
CISPR22 standard. EN55022 is now part of the EU’s
EMC Directive and compliance is expected to be
required starting in 2003. Adherence to this standard
will be necessary to display the CE mark on designs
intended for sale in the EU. The typical schematic and
global bill of materials (BOM) (see Figure 19 and
Table 16) contained in this data sheet are designed to
be compliant to the CISPR22 standard.
If smaller inductors are desired, a notch filter may be
used and compliance to CISPR22 still achieved. As
shown in Figure 35, a series capacitor-resistor in
parallel with L1 and L2 forms the simple notch filter.
Table 27 shows corresponding values used for C24,
C25, C38, C39, L1, L2, R31, and R32.
Figure 35. Notch Filter for CISPR22 Compliance
54
P P E N D I X
Table 27. Notch Filter Component Values
C24/C25 C38/C39
1000 pF
DAA
To
33 pF,
50 V
C24
C25
C38
C39
B—CISPR22 C
L1
L2
< 3
R31
R32
150 µH, DCR
Ω
, I > 120 mA
L1/L2
FB1
FB2
R31/R32
RING
1/10 W
680
TIP
Ω
,
Rev. 2.01
O M P L I A N C E
The direct current resistance (DCR) of the listed
inductors is an important consideration. If the DCR of
the inductors used is less than 3 Ω each, then country
PTT specifications which require 300 Ω or less of dc
resistance at TIP and RING with 20 mA of loop current
can be satisfied with the Japan dc termination mode. If
the DCR of the inductors is at or slightly above 3 Ω, the
low voltage termination mode may need to be used to
satisfy the 300 Ω dc resistance requirement at 20 mA of
loop
Considerations" on page 24 should be followed.
If compliance to the CISPR22 standard and certain
other country PTT requirements are not desired, then
L1 and L2 may be removed. If these inductors are
removed, C24 and C25 should be increased to 2200 pF,
and C9 should be changed to 22 nF, 250 V. With these
changes, PTT compliance in the following countries will
not be achieved: India (I/Fax-03/03 standard), Taiwan
(ID0001 standard), Chile (Decree No. 220 1981
standard), and Argentina (CNC-St2-44.01 standard).
For questions concerning compliance to CISPR22 or
other relevant standards, contact a Silicon Laboratories
technical representative.
current.
In
all
cases,
"DC
Termination