CY7C68001-56LFC Cypress Semiconductor Corp, CY7C68001-56LFC Datasheet - Page 44

• Manufacturer Part Number: CY7C68001-56LFC
• Manufacturer: Cypress Semiconductor Corp

Specifications of CY7C68001-56LFC

• Operating Temperature (min): 0C
• Operating Temperature Classification: Commercial
• Operating Temperature (max): 70C
• Rad Hardened: No
• Lead Free Status / Rohs Status: Not Compliant

Document #: 38-08013 Rev. *K
Description Title: CY7C68001 EZ-USB SX2™ High Speed USB Interface Device
Document Number: 38-08013
*D
*G
*H
*E
*F
*K
*J
*I
2665531
2733374
2896582
130447
243316
329238
392570
411515
02/26/2009
07/08/2009
See ECN
See ECN
See ECN
See ECN
12/17/03
ODC
ANTG/AESA Updated cross-references on pages 2 and 3
DPT/PYRS Added package diagram (51-85187) and updated Ordering Information table.
03/19/10
BHA
KKU
KKU
KEV
KEV
Reformatted data sheet to latest format
Provided additional timing restrictions and requirement regarding the use of
Modified
Added information in section
Replaced package diagram in
Fixed last history entry for rev *C
Change reference in section 2.7.2.4 from XXXXXXX to 7.3
Removed the word “compatible” in section 3.3
Change the text in section 5.0, last paragraph from 0xE6FB to 0xE683
Changed label “Reset” to “Default” in sections 5.1 and 7.2 through 7.14
Reformatted Figure 4
Added entries 3A, 3B, 3C, 0xE609, and 0xE683 to
Change access on hex values 07 and 09 from bbbbbbbb to bbbbrbrr
Removed t
Corrected timing diagrams, figures 11-1,11-2, 11-6
Changed
reference to t3 which should be t2, added reference of t3 for deasserting SLWR and
reworded section 11.6
Updated I
Added Lead-free parts numbers
Updated default value for address 0x07 and 0x09
Added Footnote 3.
Removed requirement of less then 360 nsec period between nibble writes in
command
Changed PKTEND to FLAGS output propagation delay in table 11-16 from a max
value of 70 ns to 110 ns
PKTEND pin to commit a short one byte/word packet subsequent to committing a
packet automatically (when in auto mode)
Miscellaneous grammar corrections.
Added 3.4.3 section header.
Fixed command sequence step 3 to say register value instead of High Byte of
Register Address (upper and lower nibble in two places).
Removed statement that programmable flag polarity is set to active low and cannot
be altered. Programmable flag relies on DECIS bit settings.
Updated Amkor application note URL.
Changed T
Changed T
Changed FLAGS Interrupt from empty to not-empty to both empty to not-empty and
from not-empty to empty conditions for triggering this interrupt.
Changed corporate address to 198 Champion Court.
enumeration.
Updated template
Updated section numbers
Removed obsolete parts from the ordering information table
Updated package diagrams
Figure 5-1.
Figure 13-16.
CC
XFD
XINT
RDY
typical and maximum values
from
in Figure 11-4 to be from deassertion edge of SLWR.
in Figure 11-3 to be from deassertion edge of SLRD.
Figure 13-9.
to fit across columns. It was getting cropped in half.
through
USB Signaling Speed
Figure 18-2.
Figure 13-21.
and
Figure 13-10.
spec number 51-85144 with clear image
for clarity, text which followed had
Figure 9-1
on page 2 on Full Speed only
and tables 11-1,2, and 5
CY7C68001
Page 44 of 45
[+] Feedback
[+] Feedback
[+] Feedback