AD7801BR-REEL7 Analog Devices Inc, AD7801BR-REEL7 Datasheet - Page 7

• Manufacturer Part Number: AD7801BR-REEL7
• Manufacturer: Analog Devices Inc

Specifications of AD7801BR-REEL7

• Number Of Channels: 1
• Resolution: 8b
• Conversion Rate: 833KSPS
• Interface Type: Parallel
• Single Supply Voltage (typ): 3.3/5V
• Dual Supply Voltage (typ): Not RequiredV
• Settling Time: 2us
• Architecture: Current Steering
• Power Supply Requirement: Single
• Output Type: Voltage
• Integral Nonlinearity Error: ±1LSB
• Single Supply Voltage (min): 2.7V
• Single Supply Voltage (max): 5.5V
• Dual Supply Voltage (min): Not RequiredV
• Dual Supply Voltage (max): Not RequiredV
• Operating Temp Range: -40C to 105C
• Operating Temperature Classification: Industrial
• Mounting: Surface Mount
• Pin Count: 20
• Package Type: SOIC W
• Lead Free Status / Rohs Status: Not Compliant

REV. 0
TERMINOLOGY
Integral Nonlinearity
For the DAC, Relative Accuracy or End-Point nonlinearity is a
measure of the maximum deviation, in LSBs, from a straight
line passing through the endpoints of the DAC transfer
function. A graphical representation of the transfer curve is
shown in Figure 14.
Differential Nonlinearity
Differential Nonlinearity is the difference between the mea-
sured change and the ideal 1 LSB change between any two
adjacent codes. A specified differential nonlinearity of 1 LSB
maximum ensures monotonicity.
Zero-Code Error
Zero-Code Error is the measured output voltage from V
the DAC when zero code (all zeros) is loaded to the DAC
latch. It is due to a combination of the offset errors in the DAC
and output amplifier. Zero-code error is expressed in LSBs.
Gain Error
This is a measure of the span error of the DAC. It is the
deviation in slope of the DAC transfer characteristic from ideal
expressed as a percent of the full-scale value. It includes full-
scale errors but not offset errors.
Digital-to-Analog Glitch Impulse
Digital-to-Analog Glitch Impulse is the impulse injected into
the analog output when the digital inputs change state with
the DAC selected and the LDAC used to update the DAC. It
is normally specified as the area of the glitch in nV-secs and
measured when the digital input code is changed by 1 LSB at
the major carry transition.
Digital Feedthrough
Digital Feedthrough is a measure of the impulse injected into
the analog output of a DAC from the digital inputs of the same
DAC, but is measured when the DAC is not updated. It is
specified in nV-secs and measured with a full-scale code change
on the data bus, i.e., from all 0s to all 1s and vice versa.
Power Supply Rejection Ratio (PSRR)
This specification indicates how the output of the DAC is affected
by changes in the power supply voltage. Power supply rejection
ratio is quoted in terms of % change in output per % change in
V
GENERAL DESCRIPTION
D/A Section
The AD7801 is an 8-bit voltage output digital-to-analog con-
verter. The architecture consists of a reference amplifier and a
current source DAC followed by a current-to-voltage converter
capable of generating rail-to-rail voltages on the output of the
DAC. Figure 19 shows a block diagram of the basic DAC
architecture.
DD
for full-scale output of the DAC. V
DD
is varied 10%.
OUT
of
–7–
The DAC output is internally buffered and has rail-to-rail
output characteristics. The output amplifier is capable of driving
a load of 100 pF and 10 k to both V
reference selection for the DAC can be either internally gener-
ated from V
comparator on the REFIN pin detects whether the required
reference is the internally generated reference or the externally
applied voltage to the REFIN pin. If REFIN is connected to
V
reference. When an externally applied voltage is more than one
volt below V
applied voltage on the REFIN pin. The range on the external
reference input is from 1.0 V to V
from the DAC is given by:
where V
V
equivalent of the code loaded to the DAC register and ranges
from 0 to 255.
DD
DD
REFIN
, the reference selected is the internally generated V
/2 when the internal reference is selected. N is the decimal
REF
V
DD
EXT REF
Figure 20. Reference Selection Circuitry
INT REF
30k
30k
DD
DD
is the voltage applied to the external REFIN pin or
, the comparator selection switches to the externally
or externally applied through the REFIN pin. A
Figure 19. DAC Architecture
REFERENCE
AMPLIFIER
REF
V
V
DD
IN
O
2V
REF
INT
PMOS
VTH
REF
CURRENT
DD
DAC
AD7801
/2 V. The output voltage
COMPARATOR
256
SELECTED REFERENCE
OUTPUT
N
11.7k
DD
MUX
and ground. The
AD7801
11.7k
I / V
DD
/2
V
OUT