PIC18F4585-H/PT Microchip Technology, PIC18F4585-H/PT Datasheet - Page 296

• Manufacturer Part Number: PIC18F4585-H/PT
• Description: IC MCU 8BIT 48KB FLASH 44TQFP
• Manufacturer: Microchip Technology
• Series: PIC® 18Fr

Specifications of PIC18F4585-H/PT

• Core Processor: PIC
• Core Size: 8-Bit
• Speed: 25MHz
• Connectivity: CAN, I²C, SPI, UART/USART
• Peripherals: Brown-out Detect/Reset, HLVD, POR, PWM, WDT
• Number Of I /o: 36
• Program Memory Size: 48KB (24K x 16)
• Program Memory Type: FLASH
• Eeprom Size: 1K x 8
• Ram Size: 3.25K x 8
• Voltage - Supply (vcc/vdd): 4.2 V ~ 5.5 V
• Data Converters: A/D 11x10b
• Oscillator Type: Internal
• Operating Temperature: -40°C ~ 150°C
• Package / Case: 44-TQFP
• Lead Free Status / Rohs Status: Lead free / RoHS Compliant

PIC18F2585/2680/4585/4680
23.2.3.1
The ECAN module contains 6 message buffers that can
be programmed as transmit or receive buffers. Any of
these buffers can also be programmed to automatically
handle RTR messages.
REGISTER 23-22: BnCON: TX/RX BUFFER n CONTROL REGISTERS IN RECEIVE MODE
DS39625C-page 294
Note:
bit 7
bit 6
bit 5
bit 4-0
These registers are not used in Mode 0.
Programmable TX/RX and
Auto-RTR Buffers
[0 ≤ n ≤ 5, TXnEN (BSEL0<n>) = 0]
bit 7
Legend:
R = Readable bit
-n = Value at POR
RXFUL: Receive Full Status bit
1 = Receive buffer contains a received message
0 = Receive buffer is open to receive a new message
RXM1: Receive Buffer Mode bit
1 = Receive all messages including partial and invalid (acceptance filters are ignored)
0 = Receive all valid messages as per acceptance filters
RXRTRRO: Read-Only Remote Transmission Request for Received Message bit
1 = Received message is a remote transmission request
0 = Received message is not a remote transmission request
FILHIT4:FILHIT0: Filter Hit bits
These bits indicate which acceptance filter enabled the last message reception into this buffer.
01111 = Acceptance Filter 15 (RXF15)
01110 = Acceptance Filter 14 (RXF14)
...
00001 = Acceptance Filter 1 (RXF1)
00000 = Acceptance Filter 0 (RXF0)
RXFUL
R/W-0
Note 1: These registers are available in Mode 1 and 2 only.
(2)
2: This bit is set by the CAN module upon receiving a message and must be cleared
by software after the buffer is read. As long as RXFUL is set, no new message will
be loaded and the buffer will be considered full.
R/W-0
RXM1
RXRTRRO
W = Writable bit
‘1’ = Bit is set
R-0
Preliminary
(2)
FILHIT4
R-0
(1)
FILHIT3
U = Unimplemented bit, read as ‘0’
‘0’ = Bit is cleared
R-0
FILHIT2
R-0
© 2007 Microchip Technology Inc.
x = Bit is unknown
FILHIT1
R-0
FILHIT0
R-0
bit 0