LM339N National Semiconductor, LM339N Datasheet - Page 4

• Manufacturer Part Number: LM339N
• Manufacturer: National Semiconductor

Specifications of LM339N

• Number Of Elements: 4
• Output Type: Open Collector
• Technology: Bipolar
• Input Offset Voltage: 5mV
• Input Bias Current (typ): 250nA
• Response Time: 1.3us
• Single Supply Voltage (typ): 3/5/9/12/15/18/24/28V
• Dual Supply Voltage (typ): ±3/±5/±9/±12/±15V
• Supply Current (max): 2@5VmA
• Power Supply Requirement: Single/Dual
• Voltage Gain In Db: 106.02dB
• Single Supply Voltage (min): 2V
• Single Supply Voltage (max): 36V
• Dual Supply Voltage (min): ±1V
• Dual Supply Voltage (max): ±18V
• Power Dissipation: 1.05W
• Operating Temp Range: 0C to 70C
• Operating Temperature Classification: Commercial
• Mounting: Through Hole
• Pin Count: 14
• Package Type: PDIP
• Lead Free Status / Rohs Status: Not Compliant

www.national.com
Output Leakage Current
Differential Input Voltage
Input Offset Voltage
Input Offset Current
Input Bias Current
Input Common-Mode
Voltage Range
Saturation Voltage
Output Leakage Current
Differential Input Voltage
(V
(V
Electrical Characteristics
Electrical Characteristics
Note 1: For operating at high temperatures, the LM339/LM339A, LM2901, LM3302 must be derated based on a 125˚C maximum junction temperature and a
thermal resistance of 95˚C/W which applies for the device soldered in a printed circuit board, operating in a still air ambient. The LM239 and LM139 must be derated
based on a 150˚C maximum junction temperature. The low bias dissipation and the “ON-OFF” characteristic of the outputs keeps the chip dissipation very small
(P
Note 2: Short circuits from the output to V
current is approximately 20 mA independent of the magnitude of V
Note 3: This input current will only exist when the voltage at any of the input leads is driven negative. It is due to the collector-base junction of the input PNP
transistors becoming forward biased and thereby acting as input diode clamps. In addition to this diode action, there is also lateral NPN parasitic transistor action
on the IC chip. This transistor action can cause the output voltages of the comparators to go to the V
duration that an input is driven negative. This is not destructive and normal output states will re-establish when the input voltage, which was negative, again returns
to a value greater than −0.3 V
Note 4: These specifications are limited to −55˚C T
−25˚C T
Note 5: The direction of the input current is out of the IC due to the PNP input stage. This current is essentially constant, independent of the state of the output so
no loading change exists on the reference or input lines.
Note 6: The input common-mode voltage or either input signal voltage should not be allowed to go negative by more than 0.3V. The upper end of the common-mode
voltage range is V
Note 7: The response time specified is a 100 mV input step with 5 mV overdrive. For larger overdrive signals 300 ns can be obtained, see typical performance
characteristics section.
Note 8: Positive excursions of input voltage may exceed the power supply level. As long as the other voltage remains within the common-mode range, the
comparator will provide a proper output state. The low input voltage state must not be less than −0.3 V
supply, if used) (at 25˚C).
Note 9: At output switch point, V
For LM3302, V
Note 10: Refer to RETS139AX for LM139A military specifications and to RETS139X for LM139 military specifications.
+
+
D
= 5.0 V
= 5.0 V
100 mW), provided the output transistors are allowed to saturate.
Parameter
Parameter
A
+85˚C, the LM339/LM339A temperature specifications are limited to 0˚C T
DC
DC
+
, (Note 4))
from 5 V
, (Note 4))
+
−1.5V at 25˚C, but either or both inputs can go to +30 V
DC
to 28 V
DC
(Note 9)
I
I
Linear Range, V
5)
V
V
(Note 6)
V
I
V
V
V
Keep all V
if used), (Note 8)
IN(+)
IN(+)
SINK
O
+
DC
IN(−)
IN(+)=
O
DC
(at 25˚)C.
.1.4 V
=30 V
=30 V
DC
V
V
V
Keep all V
if used), (Note 8)
)
)
−I
IN(+)=
O
O
or I
=1 V
.
4 mA
IN(−)
1 V
=30 V
=28 V
DC
+
IN(−)
DC
Conditions
DC
can cause excessive heating and eventual destruction. When considering short circuits to ground, the maximum output
, R
DC
1 V
, V
DC
IN
, (LM3302, V
(LM3302, V
’s 0 V
S
, V
DC
DC
, V
CM
=0
with Output in
DC
IN
Conditions
, (LM3302,
)
IN(−)
IN(+)
’s 0 V
=0V
, V
CM
with V
A
(Continued)
DC
IN(−)
=0V (Note
+125˚C, for the LM139/LM139A. With the LM239/LM239A, all temperature specifications are limited to
=0,
=0,
(or V
+
DC
=0,
from 5 V
+
O
=28
(or V
=28
−
+
,
.
DC
−
,
Min
to 30 V
LM239, LM339
DC
without damage (25V for LM3302), independent of the magnitude of V
4
DC
Typ
Min Typ
; and over the full input common-mode range (0 V
A
LM139A
+70˚C, and the LM2901, LM3302 temperature range is −40˚C T
V
Max
+
150
400
700
9.0
1.0
36
−2.0
Max
1.0
36
+
Min
voltage level (or to ground for a large overdrive) for the time
0
DC
Min Typ
(or 0.3 V
LM2901
Typ
200
400
50
9
LM239A,
LM339A
DC
V
below the magnitude of the negative power
Max
200
500
+
700
1.0
15
36
−2.0
Max
1.0
36
Min
0
Min Typ
DC
LM3302
to V
Typ
LM139
+
−1.5 V
V
1000
Max
+
300
700
1.0
Max
40
28
−2.0
1.0
DC
36
+
), at 25˚C.
.
A
+85˚C.
mV
mV
Units
Units
nA
nA
µA
µA
V
V
V
DC
DC
DC
DC
DC
DC
DC
DC
DC