ATmega32A Atmel Corporation, ATmega32A Datasheet - Page 278
ATmega32A
Manufacturer Part Number
ATmega32A
Description
Manufacturer
Atmel Corporation
Specifications of ATmega32A
Flash (kbytes)
32 Kbytes
Pin Count
44
Max. Operating Frequency
16 MHz
Cpu
8-bit AVR
# Of Touch Channels
16
Hardware Qtouch Acquisition
No
Max I/o Pins
32
Ext Interrupts
3
Usb Speed
No
Usb Interface
No
Spi
1
Twi (i2c)
1
Uart
1
Graphic Lcd
No
Video Decoder
No
Camera Interface
No
Adc Channels
8
Adc Resolution (bits)
10
Adc Speed (ksps)
15
Analog Comparators
1
Resistive Touch Screen
No
Temp. Sensor
No
Crypto Engine
No
Sram (kbytes)
2
Eeprom (bytes)
1024
Self Program Memory
YES
Dram Memory
No
Nand Interface
No
Picopower
No
Temp. Range (deg C)
-40 to 85
I/o Supply Class
2.7 to 5.5
Operating Voltage (vcc)
2.7 to 5.5
Fpu
No
Mpu / Mmu
no / no
Timers
3
Output Compare Channels
4
Input Capture Channels
1
Pwm Channels
4
32khz Rtc
Yes
Calibrated Rc Oscillator
Yes
Available stocks
Company
Part Number
Manufacturer
Quantity
Price
Company:
Part Number:
ATMEGA32A
Manufacturer:
Atmel
Quantity:
150
Part Number:
ATMEGA32A
Manufacturer:
ATMEL/爱特梅尔
Quantity:
20 000
Company:
Part Number:
ATmega32A-AU
Manufacturer:
ATMEL
Quantity:
5 600
Part Number:
ATmega32A-AU
Manufacturer:
ATMEL/爱特梅尔
Quantity:
20 000
Company:
Part Number:
ATmega32A-AUR
Manufacturer:
SMD
Quantity:
5
Part Number:
ATmega32A-MU
Manufacturer:
MICROCHIP/微芯
Quantity:
20 000
Company:
Part Number:
ATmega32A-PU
Manufacturer:
ATMEL
Quantity:
3 000
Company:
Part Number:
ATmega32A-PU
Manufacturer:
Atmel
Quantity:
26 792
26.7.12
26.7.13
8155C–AVR–02/11
Reading the Signature Bytes
Reading the Calibration Byte
Figure 26-6. Mapping between BS1, BS2 and the Fuse- and Lock Bits during Read
The algorithm for reading the Signature bytes is as follows (refer to
page 272
The algorithm for reading the Calibration byte is as follows (refer to
page 272
1. A: Load Command “0000 0100”.
2. Set OE to “0”, BS2 to “0” and BS1 to “0”. The status of the Fuse Low bits can now be
3. Set OE to “0”, BS2 to “1” and BS1 to “1”. The status of the Fuse High bits can now be
4. Set OE to “0”, BS2 to “0” and BS1 to “1”. The status of the Lock bits can now be read at
5. Set OE to “1”.
1. A: Load Command “0000 1000”.
2. B: Load Address Low Byte ($00 - $02).
3. Set OE to “0”, and BS1 to “0”. The selected Signature byte can now be read at DATA.
4. Set OE to “1”.
1. A: Load Command “0000 1000”.
2. B: Load Address Low Byte, $00.
3. Set OE to “0”, and BS1 to “1”. The Calibration byte can now be read at DATA.
4. Set OE to “1”.
read at DATA (“0” means programmed).
read at DATA (“0” means programmed).
DATA (“0” means programmed).
for details on Command and Address loading):
for details on Command and Address loading):
Fuse High Byte
Fuse Low Byte
Lock Bits
BS2
0
1
BS1
0
1
“Programming the Flash” on
“Programming the Flash” on
DATA
ATmega32A
278