ATxmega128D4 Atmel Corporation, ATxmega128D4 Datasheet - Page 82

• Manufacturer Part Number: ATxmega128D4
• Manufacturer: Atmel Corporation

Specifications of ATxmega128D4

• Flash (kbytes): 128 Kbytes
• Pin Count: 44
• Max. Operating Frequency: 32 MHz
• Cpu: 8-bit AVR
• Hardware Qtouch Acquisition: No
• Max I/o Pins: 34
• Ext Interrupts: 34
• Usb Speed: No
• Usb Interface: No
• Spi: 4
• Twi (i2c): 2
• Uart: 2
• Graphic Lcd: No
• Video Decoder: No
• Camera Interface: No
• Adc Channels: 12
• Adc Resolution (bits): 12
• Adc Speed (ksps): 200
• Analog Comparators: 2
• Resistive Touch Screen: No
• Temp. Sensor: Yes
• Crypto Engine: No
• Sram (kbytes): 8
• Eeprom (bytes): 2048
• Self Program Memory: YES
• Dram Memory: No
• Nand Interface: No
• Picopower: Yes
• Temp. Range (deg C): -40 to 85
• I/o Supply Class: 1.6 to 3.6
• Operating Voltage (vcc): 1.6 to 3.6
• Fpu: No
• Mpu / Mmu: no / no
• Timers: 4
• Output Compare Channels: 14
• Input Capture Channels: 14
• Pwm Channels: 14
• 32khz Rtc: Yes
• Calibrated Rc Oscillator: Yes

8.3
8.3.1
8.3.2
8.3.3
8.4
8.4.1
8210B–AVR–04/10
Reset Sequence
Reset Sources
Reset Counter Delay
Oscillator Startup
Oscillator Calibration
Power-On Reset
Reset request from any reset source immediately reset the device, and keep it in reset as long
as the request is active. When all reset requests are released, the device will go through three
stages before the internal reset is released and the device starts running.
If one of the reset request occur during this, the reset sequence will start over again.
The Reset Counter Delay is the programmable period from all reset requests are released and
until the reset counter times out and releases reset. The Reset Counter Delay is timed from the
1 kHz output of the Ultra Low Power (ULP) Internal Oscillator, and the number of cycles before
the timeout is set by the STARTUPTIME fuse bits. The selectable delays are shown in
1.
Table 8-1.
After the Reset Counter Delay, the default clock is started. This is the 2 MHz internal RC oscilla-
tor, and this uses 6 clock cycles to startup and stabilize.
After the default oscillator has stabilized, oscillator calibration values are loaded from Non-Vola-
tile Memory into the Oscillator Calibration registers. Loading the calibration values takes
24 clock cycles on the internal 2 MHz oscillator. The 2 MHz, 32 MHz and 32.768 kHz internal RC
oscillators are calibrated. When this is done the device will enter active mode and program exe-
cution will begin.
A Power-on detection circuit will give a Power-On Reset (POR) when supply voltage (V
applied to the device and the V
Power-on reset is released when the V
Power-on Threshold Voltage (V
When V
lower than the minimum operating voltage for the device, and is only used for power-off function-
SUT[1:0]
• Reset Counter Delay
• Oscillator startup
• Oscillator calibration
00
01
10
11
CC
is falling, the POR will issue a reset when the Vpot level is reached. The Vpot level is
Reset Counter Delay
POT
Number of 1 kHz ULP oscillator clock cycles
CC
) level.
slope is increasing in the Power-on Slope Range (V
CC
stops rising or when the V
Reserved
64
4
0
CC
level has reached the
XMEGA D
Table 8-
POSR
CC
) is
82
).